CONTINENTAL 12688607
High Pressure Fuel Pump Cadillac CT4 CT5 XT4 Buick LaCrosse Chevy Malibu 2.0T LSY
12688608, 12693821, 12682977, HPP0042, GDP112, HM10048--200 bar peak rail pressureProduct Overview
The 12688607 is an original equipment (CONTINENTAL) precision component engineered specifically for the GM 2.0L Turbo SIDI Ecotec Tripower DOHC 16V (LSY). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P053F.
Always verify the OE reference 12688608, 12693821, 12682977, HPP0042 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 12688607 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 12688607 |
| Manufacturer Brand | CONTINENTAL |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | GM 2.0L Turbo SIDI Ecotec Tripower DOHC 16V (LSY) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P053F |
| System Type | High Pressure Fuel Pump |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify the exact engine code and model year against the vehicle's EPC before installing part 12688607.
- Torque the mounting/hold-down to 13 N·m and the high-pressure line to 30 N·m.
- Check the listed DTCs P0300, P0087, P0193, P0089, and P0191 when diagnosing a suspected pump fault.
Frequently Asked Questions
Will part 12688607 fit my Cadillac ATS, Buick Regal, Buick Envision, or Chevrolet Camaro?
Part 12688607 is listed for Cadillac ATS/ATS-L 2013-2019 and Buick Regal 2014-2020 with the GM 2.0L Ecotec Turbo SIDI family (LTG / LSY Tripower / LHU). It is also listed for Buick Envision 28T AWD 2015-2020 and Chevrolet Camaro 2016-2020. Confirm the exact engine code and model year against the vehicle's EPC before ordering.
Which diagnostic trouble codes are listed for this high-pressure fuel pump?
The verified facts list P0300, P0087, P0193, P0089, and P0191. No additional symptom descriptions are stated, so confirm the diagnosis against the vehicle's EPC.
What are the hold-down and high-pressure line torques for part 12688607?
The mounting/hold-down torque is 13 N·m, and the high-pressure line torque is 30 N·m. The system pressure is 200 bar.
Does this pump require coding/adaptation, and can the seals be reused?
The verified facts do not state whether coding/adaptation is required or whether the seals can be reused. Confirm both against the vehicle's EPC before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.