Catalog / HITACHI / 12668390
HITACHI

HITACHI 12668390

View Specs
SolenoidGDI High-Pressure Fuel Pump (HPFP)Euro 6

High Pressure Fuel Pump GM Silverado Tahoe Sierra Yukon 5.3L 6.2L V8

Reference data for HITACHI 12668390 high-pressure fuel pump · OEM 12658480, 12672535, 12688607, 12697965 · Application GM 4.3L V6 & 5.3L / 6.2L EcoTec3 Gen V V8 (LV3 / L83 / L84 / L86 / L87)
OE REFERENCE12658480, 12672535, 12688607, 12697965
CONTROL VALVEINTEGRATED PULSE-WIDTH MODULATED SPILL VALVE SOLENOID
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Hitachi 12668390 (GM OE 12658480 / 12672535 / 12688607) is the factory original equipment high-pressure mechanical fuel pump for General Motors Gen V EcoTec3 5.3L L83 and 6.2L L86 V8 truck engines. Driven off a three-lobe profile on the rear of the camshaft via a dedicated roller lifter, this pump generates up to 200 bar (2900 psi) direct injection pressure. Plunger wear or solenoid sticking triggers diagnostic trouble codes P0087 (low rail pressure), P0089 (regulator performance), and lean misfire under heavy payload towing.

Before You Order

Always verify the OE reference 12658480, 12672535, 12688607, 12697965 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 12668390 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Chevrolet Silverado 1500 5.3LGM 4.3L V6 & 5.3L / 6.2L EcoTec3 Gen V V8 (LV3 / L83 / L84 / L86 / L87)2014-2020
GMC Sierra 1500 6.2LGM 4.3L V6 & 5.3L / 6.2L EcoTec3 Gen V V8 (LV3 / L83 / L84 / L86 / L87)2014-2020
Cadillac Escalade 6.2LGM 4.3L V6 & 5.3L / 6.2L EcoTec3 Gen V V8 (LV3 / L83 / L84 / L86 / L87)2015-2020
04

Technical Specifications

SpecificationValue
Pump GenerationHitachi Radial Plunger High-Pressure Mechanical Fuel Pump
Operating Rail PressureCore Spec
Cam Drive TypeExhaust Camshaft Tri-Lobe via Roller Lifter (GM 12659746)
Flow Regulation ControlIntegrated Pulse-Width Modulated Spill Valve Solenoid
Pump Flange Mounting Torque12 N·m + 45° (Even two-stage torque)
High Pressure Pipe Flare Nut Torque30 N·m
Tightening Torque30 N·m
Primary OEM Reference12668390, 12658480, 12672535, 12688607
Engine Emission ComplianceEuro 6 / LEV III / Tier 3 Bin 30
Standard Industrial Warranty12 Months / Unlimited Mileage

Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)

Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.

DELPHIExact Engine & Chassis Match
12638824
Gasoline Direct Injection (GDI) • 150 bar
🚙 Engine Code L83
Technical Specifications & Pinout
HITACHIExact Engine & Chassis Match
12668649
Gasoline Direct Injection (GDI) • 150 bar
🚙 Engine Code L83
Technical Specifications & Pinout
DELPHIExact Engine & Chassis Match
12692223
Gasoline Direct Injection (GDI) • 150 bar
🚙 Engine Code L83
Technical Specifications & Pinout
05

Installation Tips

Tools needed: 10mm socket, swivel extension, and torque wrench for pump mounting bolts, 17mm line flare nut wrench for high-pressure steel fuel pipe, Torque wrench calibrated for 10-35 N·m range, Clean engine oil or assembly lube for roller lifter and O-ring seal, Heavy shop towels and eye protection for residual fuel containment

  1. Disconnect vehicle battery; remove fuel pump fuse and crank engine for 5 seconds to depressurize low-pressure fuel line.
  2. Wrap shop towels around fuel line connection and slowly crack open high-pressure line flare nut to relieve residual rail pressure.
  3. Disconnect electrical wiring harness from the fuel volume control spill valve solenoid.
  4. Disconnect low-pressure fuel supply line quick-connect coupler from the pump inlet fitting.
  5. Loosen the two pump flange bolts evenly in alternating half-turn increments to relieve camshaft spring tension squarely.
  6. Withdraw pump assembly from the cylinder head; extract roller lifter GM 12659746 and inspect roller surface for pitting, flat spots, or axial play.
  7. Clean the pump mounting recess; lubricate new pump O-ring seal and new roller lifter with fresh engine oil.
  8. Rotate crankshaft manually until the camshaft drive lobe is positioned at its base circle (lowest point of travel).
  9. Install lubricated roller lifter into bore; seat fuel pump squarely into position and install mounting bolts finger-tight.
  10. Torque mounting bolts evenly in progressive passes to 12 N·m, followed by a final 45-degree angle turn.
  11. Start high-pressure line flare nut by hand to guarantee proper thread engagement; torque flare nut to 30 N·m.
  12. Reconnect low-pressure feed line and spill valve electrical connector; prime fuel system by keying ignition on for 10 seconds prior to starting.
Tips & Warnings:
  • Cam Base Circle Positioning: Always verify the camshaft drive lobe is on base circle prior to torquing mounting bolts to avoid cocking the pump body against spring tension.
  • Oil Dilution Verification: Sniff the engine oil dipstick for raw gasoline odor; if fuel dilution is detected, perform a complete engine oil and filter change immediately.
06

Frequently Asked Questions

QWhat are the primary symptoms when 12668390 fails?

Primary symptoms include extended cold engine cranking, severe hesitation under wide-open throttle, rough idle RPM fluctuation, and Diagnostic Trouble Codes P0087 (Fuel Rail/System Pressure Too Low), P0089 (Fuel Pressure Regulator Performance), or P0300 (Random/Multiple Cylinder Misfire).

QWhat is the exact tightening torque for 12668390?

The holding flange mounting torque is 12 N·m + 45°, and the high-pressure fuel pipe union nut must be torqued to 30 N·m.

QCan I reuse the seals when replacing 12668390?

No. All high-pressure fuel seals, including Viton O-rings and combustion chamber Teflon rings, are strictly single-use. Reusing compressed seals will cause pressurized fuel leaks or combustion blowby into the cylinder head.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol