Catalog / DELPHI / 12638824
DELPHI

DELPHI 12638824

View Specs
Direct Cylinder High-Pressure Electromagnetic Multi-Hole InjectorGasoline Direct Injection (GDI / HDEV)Euro 6

High Pressure Fuel Injector Chevrolet Silverado Tahoe Suburban GMC Sierra Yukon 5.3L 6.2L V8 EcoTec3 FJ1217

Reference data for DELPHI 12638824 common rail injector · OEM 12698484, 12661031, 217-3445, FJ1217, 12672368 · Application GM 4.3L V6 & 5.3L / 6.2L EcoTec3 Gen V V8 (LV3 / L83 / L84 / L86 / L87)
OE REFERENCE12698484, 12661031, 217-3445, FJ1217, 12672368
CONTROL VALVE-
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Delphi / GM 12638824 (FJ1217, superseded by 12698484) direct petrol injector delivers atomized fuel directly into the combustion bowl of General Motors' Gen V Small Block V8 engines (L83 5.3L and L86 6.2L). Operating under fuel rail pressures up to 150 bar (2175 psi), these low-impedance electromagnetic injectors utilize a high-voltage boost phase (65 volts) to open the pintle against peak cylinder pressures. Direct injection enables compression ratios of 11.0:1 on the 5.3L and 11.5:1 on the 6.2L while operating safely on pump fuel.

Before You Order

Always verify the OE reference 12698484, 12661031, 2173445, FJ1217 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 12638824 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Chevrolet Silverado 1500 / Tahoe / SuburbanGM 4.3L V6 & 5.3L / 6.2L EcoTec3 Gen V V8 (LV3 / L83 / L84 / L86 / L87)2014-2021
GMC Sierra 1500 / YukonGM 4.3L V6 & 5.3L / 6.2L EcoTec3 Gen V V8 (LV3 / L83 / L84 / L86 / L87)2014-2021
04

Technical Specifications

SpecificationValue
Operating PressureCore Spec
Injector TechnologyHigh-Pressure Direct Cylinder Electromagnetic Solenoid
Coil Resistance1.3 - 1.7 Ohms (Low Impedance Peak-and-Hold)
Seal DesignVirgin Teflon Combustion Chamber Radial Seal
Fuel Rail Fastener Torque12 N·m
Jumper Line Torque30 N·m
Flow Rate126 g/min @ 100 bar test fluid
OE Cross References12638824, 12668390, 12698484, 12661031, 217-3445, FJ1217
Failure SymptomsRough cold idle, misfires (P0300-P0308), rich codes (P0172/P0175), fuel wash, catalytic converter damage
Diagnostic TestAutomated injector balance pressure drop test via GDS2 scan tool

Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)

Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.

HITACHIExact Engine & Chassis Match
12692511
Gasoline Direct Injection (GDI) • 150 bar
🚙 Chevrolet Silverado 1500 / Tahoe / Suburban (L83)
Technical Specifications & Pinout
HITACHIExact Engine & Chassis Match
12694551
Gasoline Direct Injection (GDI) • 150 bar
🚙 Chevrolet Silverado 1500 / Tahoe / Suburban (L83)
Technical Specifications & Pinout
GMExact Engine & Chassis Match
12698485
Gasoline Direct Injection (GDI) • 200 bar
🚙 Chevrolet Silverado 1500 / Tahoe / Suburban (L83)
Technical Specifications & Pinout
HITACHIExact Engine & Chassis Match
12668390
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code L83
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
12698944
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code L83
Technical Specifications & Pinout
05

Installation Tips

  1. Depressurize fuel system and disconnect battery; remove intake manifold and fuel rail heat shields.
  2. Remove high-pressure cross-over fuel pipe and discard single-use high pressure metal line seals.
  3. Remove fuel rail retaining bolts and use special slide hammer puller tool (EN-47218) to lift rail assembly.
  4. Carefully unclip suspect injectors from the fuel rail; inspect injector bores in the cylinder head.
  5. Install brand new Teflon combustion seals using seal sizing tool (EN-48266) to ensure compression recovery.
  6. Apply clean engine oil sparingly to top O-rings; insert injectors firmly into rail retaining clips.
  7. Seat fuel rail into cylinder heads squarely and torque mounting bolts in two passes: 5 N·m then final 12 N·m.
  8. Install new intermediate crossover pipe and torque flare fittings to 30 N·m; clear all misfire codes.
Tips & Warnings:
  • Confirm part number 12638824 and the listed cross references before installation.
  • Tighten the mounting/hold-down to 12 N·m and the high-pressure line to 30 N·m.
  • Check the listed DTCs P0300, P0301, P0087, P0302, and P0304 during diagnosis.
06

Frequently Asked Questions

QWill this injector fit my 2014-2021 Silverado/Sierra or SUV?

Part 12638824 is a gasoline direct-injection injector for the GM 4.3L V6 and 5.3L/6.2L EcoTec3 Gen V V8 (LV3/L83/L84/L86/L87). Listed fitment is Chevrolet Silverado 1500, Tahoe, Suburban and GMC Sierra 1500, Yukon for 2014-2021. Confirm the exact vehicle against its EPC using 12638824 and the listed cross references before ordering.

QWhat DTCs should I check if I suspect this injector?

The verified diagnostic trouble codes for this listing are P0300, P0301, P0087, P0302, and P0304. No other diagnostic mapping is stated, so confirm any diagnosis against the vehicle's EPC/service information instead of guessing.

QWhat are the mounting/hold-down and high-pressure line torque specifications?

The mounting/hold-down torque is 12 N·m, and the high-pressure line torque is 30 N·m. The system pressure is 150 bar.

QHow can I verify the old injector and cross-reference before replacement?

Check the old unit against part number 12638824 and the cross references 12698484, 12661031, 2173445, FJ1217, and 12672368. No visual identification procedure is stated in the verified facts, so confirm fitment against the vehicle's EPC before installation.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
DIESEL WORKSHOP DIAGNOSTIC SOP

Cylinder Balance & Injector Deviation Guide

Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol