DELPHI 12692223
Direct Fuel Injector Chevy Silverado Tahoe Suburban GMC Sierra Yukon 5.3L 6.2L EcoTec3 V8
12668652, 12656932, 12692224, FJ1217, 12684125--150 bar peak rail pressureProduct Overview
The 12692223 is an original equipment (DELPHI) precision component engineered specifically for the GM 5.3L & 6.2L EcoTec3 V8 Direct Injection DOHC (L83 / L84 / L86 / L87). Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0174.
Always verify the OE reference 12668652, 12656932, 12692224, FJ1217 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 12692223 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 12692223 |
| Manufacturer Brand | DELPHI |
| Component Type | Direct Fuel Injector |
| Engine Application | GM 5.3L & 6.2L EcoTec3 V8 Direct Injection DOHC (L83 / L84 / L86 / L87) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 10 N-m (89 lb-in) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0174 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 10 N-m (89 lb-in).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify the engine family and vehicle application against the EPC before ordering part 12692223.
- Torque the injector mounting / hold-down fastener and high-pressure line to the listed 10 N·m values.
- Treat P0300, P0301, P0087, P0302, and P0304 as diagnostic leads and confirm the fault before replacing the injector.
Frequently Asked Questions
Will part 12692223 fit my GM truck or SUV with a 4.3L V6 or 5.3L/6.2L EcoTec3 Gen V V8?
Part 12692223 is a gasoline direct-injection injector for GM 4.3L V6 and 5.3L/6.2L EcoTec3 Gen V V8 engines in the LV3 / L83 / L84 / L86 / L87 family. Fitment includes Chevrolet Silverado 1500 / Tahoe / Suburban and GMC Sierra 1500 / Yukon for 2014-2021. Confirm the exact engine and vehicle application against the vehicle’s EPC before ordering.
Which diagnostic trouble codes are listed for this injector, and what should I do next?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. The provided facts do not include a symptom or test procedure, so confirm the diagnosis against the vehicle’s service information before replacing the injector.
What system pressure and installation torques are specified for this injector?
The system pressure is 150 bar. The mounting / hold-down torque is 10 N·m, and the high-pressure line torque is 10 N·m.
How can I verify the old injector and confirm coding or seal reuse?
Compare the old part against the listed cross references: 12692223, 12668652, 12656932, 12692224, FJ1217, and 12684125. The provided facts do not state coding / adaptation requirements or seal-reuse guidance for this injector. Confirm those details against the vehicle’s EPC or service information.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.