DENSO 23209-31120
D 4S Fuel Injector Toyota Highlander Sienna Tacoma Lexus RX350 3.5L V6 2GR FKS
23209-0P050, 23209-0P051, 23209-39215, FJ1274--200 bar peak rail pressureProduct Overview
The 23209-31120 is an original equipment (DENSO) precision component engineered specifically for the Toyota 3.5L V6 24V DOHC Dual VVT-iW D-4S Direct & Port Injection (2GR-FKS / 2GR-FXS). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P0174.
Always verify the OE reference 232090P050, 232090P051, 2320939215, FJ1274 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 23209-31120 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 23209-31120 |
| Manufacturer Brand | DENSO |
| Component Type | Direct Fuel Injector |
| Engine Application | Toyota 3.5L V6 24V DOHC Dual VVT-iW D-4S Direct & Port Injection (2GR-FKS / 2GR-FXS) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 21 N-m (15 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P0174 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 21 N-m (15 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the system pressure is 200 bar before working on the gasoline direct-injection injector.
- Torque the injector mounting/hold-down to 10 N·m and the high-pressure line to 21 N·m.
- Cross-check part number 23209-31120 against the listed cross references before installation.
Frequently Asked Questions
Will this injector fit my Tacoma, Highlander, or RX350?
This gasoline direct-injection injector, part number 23209-31120, is listed for Toyota Tacoma N300 2016-2023, Toyota Highlander XU50 2017-2022, and Lexus RX350 AL20 2016-2022 with engine codes 2GR-FKS, 2GR-FXS, or 2GR-FE. Confirm fitment against the vehicle’s EPC before ordering.
What diagnostic trouble codes are listed for this injector?
The diagnostic trouble codes listed for this gasoline direct-injection injector listing are P0300, P0301, P0087, P0302, and P0304. The listing does not state other symptoms, so confirm any fault against the vehicle’s service information and EPC.
Does this injector require coding or adaptation, and can I reuse the seals?
The provided facts do not state whether this injector requires coding or adaptation, and they do not state seal-reuse guidance. Confirm both against the vehicle’s EPC/service information before installation.
How can I verify the old injector before replacement?
Check the old injector against part number 23209-31120 and the listed cross references: 2320931120, 232090P050, 232090P051, 2320939215, FJ1274, and 231000P040. If the old part does not match, confirm fitment against the vehicle’s EPC before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.