BOSCH A2700700501
High Pressure Fuel Pump Mercedes Benz A200 B200 CLA200 GLA200 M270 1.6T 2.0T 0261520213
A2700700101, 2700700101, 0261520213--200 bar peak rail pressureProduct Overview
The A2700700501 is an original equipment (BOSCH) precision component engineered specifically for the Mercedes-Benz M270 1.6L & 2.0L Turbocharged DOHC 16V Direct Injection I4. Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P053F.
Always verify the OE reference A2700700101, 2700700101 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. A2700700501 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Mercedes-Benz C-Class (W205) | M270 / M274 | 2014-2020 |
| Mercedes-Benz E-Class (W213) | M270 / M274 | 2016-2020 |
| Mercedes-Benz GLC-Class (X253) | M270 / M274 | 2015-2020 |
| Mercedes-Benz CLA-Class (C117) | M270 / M274 | 2013-2019 |
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | A2700700501 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Mercedes-Benz M270 1.6L & 2.0L Turbocharged DOHC 16V Direct Injection I4 |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 20 N-m (177 lb-in) |
| Fuel Line / Rail Torque | 27 N-m (20 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P053F |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (177 lb-in), and torque fuel line fittings to 27 N-m (20 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm A2700700501 and M270/M274 fitment against the vehicle EPC before installation.
- Tighten the mounting/hold-down fasteners to 20 N·m.
- Tighten the high-pressure line to 27 N·m.
Frequently Asked Questions
Will part A2700700501 fit my Mercedes-Benz with an M270 or M274 engine?
It is listed for M270/M274 1.6L and 2.0L BlueDIRECT Turbo applications in C-Class W205 2014-2020, E-Class W213 2016-2020, GLC-Class X253 2015-2020, and CLA-Class C117 2013-2019. Confirm the exact vehicle and engine against the vehicle EPC before ordering.
What pressure and torque values apply to this high-pressure fuel pump?
The listed system pressure is 200 bar. The mounting/hold-down torque is 20 N·m, and the high-pressure line torque is 27 N·m. Confirm any vehicle-specific procedures against the vehicle EPC before installation.
Does this high-pressure fuel pump require coding or adaptation, and can the seals be reused?
Coding/adaptation requirements and seal reuse are not stated in the verified facts. Confirm these points against the vehicle EPC before installation.
How do I verify the old pump and know whether this replacement is the correct part?
Compare the old unit against part number A2700700501 and the listed cross references A2700700101, 2700700101, 0261520213, A2820700001, and 2700700501. If the number or vehicle application does not match, confirm against the vehicle EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.