HITACHI 16600-5CA0A
High Pressure Fuel Injector Infiniti Q50 Q60 Nissan Z 3.0T VR30DDTT FIJ0041
FIJ0041, 16600-5CA0BHIGH-SPEED ELECTROMAGNETIC MULTI-HOLE MICRO NOZZLE-200 bar peak rail pressureProduct Overview
The Hitachi 16600-5CA0A (FIJ0041) is a high-pressure multi-hole direct gasoline injector for Nissan and Infiniti 3.0L twin-turbo V6 VR30DDTT engines. It is listed for the Infiniti Q50 Red Sport 400 (2016-2024), Q60 Coupe (2017-2022) and Nissan Z RZ34 (2023-2024). It operates at up to 200 bar (20 MPa / 2900 psi) with a precision multi-hole fan pattern engineered for twin-turbo high-swirl combustion; coil resistance is 1.8-2.2 Ω at 20°C. Flanged rail bracket retaining bolts take 10 N·m and the delivery flare nut 28 N·m. Common codes are P0300, P0301-P0306 and P0171. Fit new Teflon combustion seals with a resizing tool and replace the copper backup washers.
Always verify the OE reference FIJ0041, 166005CA0B stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16600-5CA0A needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Hitachi High-Pressure Multi-Hole Direct Gasoline Fuel Injector |
| Operating PressureCore Spec | |
| Spray Pattern | Precision multi-hole fan pattern engineered for twin-turbo high-swirl combustion |
| Fuel Rail Bolt Torque | 10 N·m (flanged rail bracket retaining bolts) |
| High Pressure Pipe Torque | 28 N·m (delivery flare nut connection) |
| Coil Resistance | 1.8 - 2.2 Ω at 20°C (direct pulse solenoid circuit) |
| Common Fault Codes | P0300 (Random Misfire), P0301-P0306 (Cylinder Misfire), P0171 (System Lean under Boost) |
| Workshop Precaution | Always fit new Teflon combustion seals with resizing tool and replace copper backup washers |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel Rail & Remove Upper Intake Plenum: Disable low-pressure fuel pump fuse and crank engine until fuel pressure drops below 5 bar. Detach dual charge air intercooler ducting and intake manifold plenum.
- Disconnect Harness Plugs & Twin High Pressure Fuel Rails: Unclip wiring harness from all six direct injectors. Unscrew high pressure fuel rail retaining bolts (10 N·m) and ease fuel rails away from cylinder heads.
- Extract Injectors & Calibrate New Teflon Combustion Seals: Withdraw direct injectors using specialized slide puller. Clean cylinder head injector bores thoroughly and size new Teflon tip seals using calibration collet.
- Torque Rail Fasteners & Verify Zero High Pressure Leakage: Lubricate O-rings with clean engine oil and push injectors into position. Tighten rail bolts to 10 N·m and flare nuts to 28 N·m. Prime fuel system and inspect for leaks.
- Before fitting, verify the replacement injector part number 16600-5CA0A against the vehicle's EPC and workshop data.
- Do not assume coding, seal reuse, or service life; confirm those details in the vehicle's workshop manual for the listed application.
- After installation, follow the vehicle-specific diagnostic and adaptation procedure from the workshop manual rather than treating the injector as plug-and-play.
Frequently Asked Questions
Will this injector fit my Infiniti or Nissan?
This injector is listed for the Nissan/Infiniti gasoline direct-injection applications shown in the product fitment; confirm your VIN or EPC match before ordering.
What symptoms indicate a failed injector?
The listing does not state failure symptoms; use the vehicle's workshop diagnostic data to confirm whether the injector is at fault before replacing it.
What should I check before ordering?
Verify that the part number 16600-5CA0A matches your vehicle's EPC or workshop data, and confirm the listed Nissan/Infiniti application and any connector or seal requirements.
Does the old injector need to be matched or adapted?
Coding or adaptation requirements are not stated here; confirm injector matching, adaptation, and relearn steps against the vehicle's EPC or workshop manual before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.