DENSO 16611AA810
High Pressure Fuel Injector Subaru BRZ Toyota GR86 2.4L FA24D D 4S SU003 08670
SU003-08670, 297500-1430PRECISION HIGH-SPEED SOLENOID MULTI-HOLE NOZZLE-200 bar peak rail pressureProduct Overview
The Denso 16611AA810 (SU003-08670) is a multi-hole direct gasoline injector for Subaru and Toyota 2.4L boxer DIT / D-4S engines (FA24D). It is listed for the Subaru BRZ ZD8 and Toyota GR86 ZN8 (2022-2024). The injector operates at up to 200 bar (20 MPa / 2900 psi) and uses a 6-hole laser-calibrated spray targeted at the boxer piston crown bowl; coil resistance is 1.7-2.1 Ω at 20°C. Holding bracket flanged bolts are specified at 19 N·m and the high-pressure pipe flare nut at 32 N·m. Diagnostic codes for this fitment are P0300, P0301-P0304 and P0171. A new Teflon combustion seal ring must be fitted with a cone expansion tool before the injector goes into the boxer cylinder head.
Always verify the OE reference SU00308670, 2975001430 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16611AA810 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Denso Multi-Hole Direct Gasoline Fuel Injector |
| Operating PressureCore Spec | |
| Spray Pattern | 6-hole laser-calibrated spray targeted at boxer piston crown bowl |
| Fuel Rail Bolt Torque | 19 N·m (holding bracket flanged bolts) |
| High Pressure Pipe Torque | 32 N·m Flare Nut Connection |
| Coil Resistance | 1.7 - 2.1 Ω at 20°C (High-speed pulse driver circuit) |
| Common Fault Codes | P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0171 (System Too Lean) |
| Workshop Precaution | Replace Teflon combustion seal ring using cone expansion tool before inserting into boxer cylinder head |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Direct Injection System & Remove Strut Braces: Depressurize direct injection circuit via fuel pump fuse pull and crank engine. Unbolt engine bay cross-strut braces to access boxer cylinder heads.
- Unplug Injector Harness & Disconnect Fuel Rail Lines: Disconnect direct injection harness connectors. Loosen steel fuel rail flare nuts (32 N·m) and unbolt fuel rail mounting bolts (19 N·m).
- Extract Injectors & Install New Teflon Combustion Rings: Carefully remove injectors with puller tool. Expand replacement Teflon combustion seals onto nozzle tip and compress with sizing die.
- Seat Injectors, Torque Rail Fasteners & Verify Sealing: Push injectors into cylinder head ports. Torque rail bolts to 19 N·m. Tighten steel fuel line flare nut to 32 N·m. Check for fuel leaks on initial startup.
- Confirm fitment for the BRZ ZD8 or GR86 ZN8 application against the vehicle's EPC before installation.
- Observe the listed 19 N·m mounting/hold-down torque and 32 N·m high-pressure line torque.
- Use the listed diagnostic trouble codes P0300, P0301, P0302, P0304 and P0087 when diagnosing the injector.
Frequently Asked Questions
Will this injector fit my Subaru BRZ or Toyota GR86?
This gasoline direct-injection injector, part number 16611AA810, is listed for Subaru BRZ ZD8 2.4L Boxer FA24D 173kW (2022-2024) and Toyota GR86 ZN8 2.4L Boxer FA24D 173kW (2022-2024). The listed engine family is Subaru/Toyota 2.0L & 2.4L Boxer DIT / D-4S (FA20D / FA20F / FA24D / FA24F). Exact fitment beyond the listed applications must be confirmed against the vehicle's EPC.
What fault codes are listed for this injector?
The verified diagnostic trouble codes for this injector listing are P0300, P0301, P0302, P0304 and P0087. A symptom list is not stated in the verified facts, so confirm any symptom-based diagnosis against the vehicle's service information instead of assuming a symptom pattern.
What torques and system pressure apply to this injector?
The listed mounting/hold-down torque is 19 N·m, and the high-pressure line torque is 32 N·m. The system pressure is 200 bar. Any additional installation or adaptation step must be confirmed against the vehicle's EPC/service information.
How can I verify the old injector and cross-reference it?
Compare the old injector's part number with 16611AA810 and the listed cross references: SU00308670, 2975001430, 166005CA0A, 2320924010, 16625AA040. If the old number is unclear or not listed, confirm fitment against the vehicle's EPC. Coding or adaptation requirements are not stated in the verified facts and must be confirmed.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.