DENSO SU003-00417
Fuel Injector Toyota 86 Subaru BRZ Forester 2.0L FA20D D 4S 16600 JB00A
16600-JB00A, 23209-46010, FJ1196--130 bar peak rail pressureProduct Overview
The SU003-00417 is an original equipment (DENSO) precision component engineered specifically for the Subaru-Toyota 2.0L Boxer D-4S DOHC 16V (FA20D / FA20). Operating at peak injection pressures up to 130 bar (1885 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0171, P117B.
Always verify the OE reference 16600JB00A, 2320946010, FJ1196 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. SU003-00417 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | SU003-00417 |
| Manufacturer Brand | DENSO |
| Component Type | Direct Fuel Injector |
| Engine Application | Subaru-Toyota 2.0L Boxer D-4S DOHC 16V (FA20D / FA20) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 19 N-m (14 lb-ft) |
| Fuel Line / Rail Torque | 21 N-m (15 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0171, P117B |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 19 N-m (14 lb-ft), and torque fuel line fittings to 21 N-m (15 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Tighten the injector mounting/hold-down to 19 N·m and the high-pressure line to 21 N·m.
- Confirm the system pressure is 130 bar before diagnosing this gasoline direct-injection injector.
- Verify the old part against part number SU003-00417 and cross references SU00300417, 16600JB00A, 2320946010, FJ1196, 16611AA810, and 16625AA010.
Frequently Asked Questions
Will this injector fit my Subaru BRZ or Toyota GR86?
It is listed for Subaru BRZ ZD8 2.4L Boxer FA24D 173kW (2022-2024) and Toyota GR86 ZN8 2.4L Boxer FA24D 173kW (2022-2024). The listed engine family is Subaru/Toyota 2.0L & 2.4L Boxer DIT / D-4S (FA20D / FA20F / FA24D / FA24F). Confirm exact vehicle fitment against the vehicle's EPC.
What DTCs are listed for this gasoline direct-injection injector?
The verified diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. Diagnose the vehicle before replacement; no other symptom or failure-mode detail is stated in the verified facts.
Do I need coding/adaptation or new seals?
No coding, adaptation, or seal-reuse instruction is stated in the verified facts. Confirm both against the vehicle's EPC before installation.
How can I verify the old part?
Compare the old injector with part number SU003-00417 and cross references SU00300417, 16600JB00A, 2320946010, FJ1196, 16611AA810, and 16625AA010. If the markings do not match, confirm fitment against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.