HITACHI 16625-AA010
High Pressure Fuel Pump Subaru WRX Forester XT 2.0T FA20F DIT HPP0020
16625-AA011, HPP0020, GDP502--150 bar peak rail pressureProduct Overview
The 16625-AA010 is an original equipment (HITACHI) precision component engineered specifically for the Subaru 2.0L FA20F DIT Turbocharged Boxer DOHC 16V (FA20 DIT). Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference 16625AA011, HPP0020, GDP502 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 16625-AA010 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16625-AA010 |
| Manufacturer Brand | HITACHI |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Subaru 2.0L FA20F DIT Turbocharged Boxer DOHC 16V (FA20 DIT) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 25 N-m (18 lb-ft) |
| Fuel Line / Rail Torque | 32 N-m (24 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 25 N-m (18 lb-ft), and torque fuel line fittings to 32 N-m (24 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Tighten the mounting/hold-down fasteners to 25 N·m.
- Tighten the high-pressure line to 32 N·m.
- Confirm coding/adaptation, seal reuse, and any non-listed fitment against the vehicle's EPC/service information before installation.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Subaru BRZ ZD8 or Toyota GR86 ZN8 2.4L?
It is listed for Subaru BRZ ZD8 2.4L Boxer FA24D 173 kW (2022-2024) and Toyota GR86 ZN8 2.4L Boxer FA24D 173 kW (2022-2024). It is also associated with the Subaru/Toyota 2.0L & 2.4L Boxer DIT / D-4S engine family (FA20D / FA20F / FA24D / FA24F). For any other vehicle or engine, confirm fitment against the vehicle's EPC using part number 16625-AA010.
What diagnostic trouble codes are listed for this pump, and what symptoms should I expect?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. Specific symptom-to-failure mapping is not stated in the verified facts, so do not guess from a code alone; confirm diagnosis against the vehicle's EPC/service information.
Does this high-pressure fuel pump require coding or adaptation after installation, and can I reuse the seals?
Coding/adaptation requirements and seal reuse are not stated in the verified facts. Confirm any coding, adaptation, or seal-reuse procedure against the vehicle's EPC/service information rather than guessing.
What are the torque specs, system pressure, and part number/cross references for this pump?
Mounting/hold-down torque is 25 N·m and high-pressure line torque is 32 N·m; listed system pressure is 150 bar. The part number is 16625-AA010. Listed cross references are 16625AA010, 16625AA011, HPP0020, GDP502, 16611AA720, and SU00300417. Confirm any other fitment or marking against the vehicle's EPC rather than guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.