DENSO 23100-36010
High Pressure Fuel Pump Toyota Highlander Lexus NX200t RX200t 2.0T 8AR FTS 297500 0120
23100-36011, 297500-0120, 297500-0121, GDP201--200 bar peak rail pressureProduct Overview
The 23100-36010 is an original equipment (DENSO) precision component engineered specifically for the Toyota-Lexus 2.0L Turbo D-4ST DOHC 16V (8AR-FTS). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P1604.
Always verify the OE reference 2310036011, 2975000120, 2975000121, GDP201 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 23100-36010 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 23100-36010 |
| Manufacturer Brand | DENSO |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Toyota-Lexus 2.0L Turbo D-4ST DOHC 16V (8AR-FTS) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 21 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 30 N-m (22 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P1604 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 21 N-m (15 lb-ft), and torque fuel line fittings to 30 N-m (22 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm part number 23100-36010 and cross references 2310036010, 2310036011, 2975000120, 2975000121, GDP201, and 2320936010 against the vehicle's EPC before installation.
- Torque the mounting/hold-down fasteners to 21 N·m and the high-pressure line to 30 N·m.
- Verify the engine family is Toyota/Lexus 2.0L Turbo 8AR-FTS D-4ST before fitting the pump.
Frequently Asked Questions
Will this high-pressure fuel pump fit my vehicle?
This pump is listed for Toyota Highlander 8AR-FTS (2015-2021), Toyota Crown S210 8AR-FTS (2015-2020), Lexus RX AL20 8AR-FTS (2015-2022), and Lexus NX AZ10 8AR-FTS (2014-2021). It is for the Toyota/Lexus 2.0L Turbo 8AR-FTS D-4ST DOHC 16V engine family and carries part number 23100-36010. Confirm fitment against the vehicle's EPC before ordering.
What are the mounting and high-pressure line torque values?
The mounting/hold-down torque is 21 N·m, and the high-pressure line torque is 30 N·m. This pump is listed with a system pressure of 200 bar.
Does this high-pressure fuel pump require coding or adaptation after installation?
Coding or adaptation requirements are not stated in the supplied facts. Confirm this against the vehicle's EPC or service information instead of guessing.
Which diagnostic trouble codes are listed, and do they prove the pump is failed?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. The supplied facts do not state that these codes alone prove the high-pressure fuel pump is failed. Confirm the diagnosis against the vehicle's EPC or service information.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.