BOSCH 31478897
High Pressure Fuel Pump Volvo XC90 XC60 S90 V90 S60 2.0T Drive E B4204T 0261520288
31375604, 31686568, HPP0048, GDP226, 0261520288--200 bar peak rail pressureProduct Overview
The 31478897 is an original equipment (BOSCH) precision component engineered specifically for the Volvo Drive-E 2.0L Turbocharged & Supercharged DOHC 16V I4 (B4204T / B4204T23 / B4204T27 / T5 / T6). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P053F.
Always verify the OE reference 31375604, 31686568, HPP0048, GDP226 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 31478897 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 31478897 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Volvo Drive-E 2.0L Turbocharged & Supercharged DOHC 16V I4 (B4204T / B4204T23 / B4204T27 / T5 / T6) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 27 N-m (20 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P053F |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 27 N-m (20 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm part number 31478897 and the listed cross references against the vehicle’s EPC before installation.
- Tighten the mounting/hold-down fasteners to 13 N·m and the high-pressure line to 27 N·m.
- Verify coding/adaptation and seal-reuse requirements against the vehicle’s service information before startup.
Frequently Asked Questions
Which Volvo models and engines does part 31478897 fit?
Part 31478897 fits Volvo XC90 II with B4204T (2016-2024), Volvo XC60 II with B4204T (2018-2024), and Volvo S90 II with B4204T (2017-2024). It is listed for the Volvo 2.0L Drive-E Turbo & Twin-Charged B4204T / T5 / T6 / T8 engine family. Confirm the exact application against the vehicle’s EPC.
What DTCs or symptoms are listed for this high-pressure fuel pump?
The diagnostic trouble codes stated for this listing are P0300, P0087, P0193, P0089, and P0191. Other symptom details or expected service life are not stated in the verified facts, so confirm them against the vehicle’s EPC/service information.
What are the mounting, high-pressure line, and system pressure specifications?
The mounting/hold-down torque is 13 N·m and the high-pressure line torque is 27 N·m. The listed system pressure is 200 bar for this gasoline direct-injection high-pressure fuel pump.
Does this pump need coding/adaptation, and how can I verify the old unit?
Coding/adaptation requirements and seal-reuse guidance are not stated in the verified facts; confirm them against the vehicle’s EPC/service information. To verify the old unit, check the listed cross references: 31478897, 31375604, 31686568, HPP0048, GDP226, and 0261520288. Confirm the final match by VIN/EPC before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.