HITACHI 03C127026R
High Pressure Fuel Pump Volkswagen Golf 5 6 Tiguan Touran Scirocco Audi A1 A3 1.4 TSI EA111 HPP0005
03C127026P, 03C127026M, 03C127026J, HPP0005, HM10018INTEGRATED FUEL METERING VALVE N290-150 bar peak rail pressureProduct Overview
The Hitachi 03C127026R (HPP0005) high-pressure mechanical fuel pump (HPFP) provides direct fuel pressurization for Volkswagen Group's celebrated EA111 1.4 TSI engine family, including both single-turbo (90kW / 122hp) and Twincharged (supercharger + turbocharger, 118-136kW / 160-185hp) variants. Mounted to the cylinder head, the pump is actuated by an intake camshaft drive lobe via a roller follower tappet, delivering operational rail pressures up to 150 bar (2175 psi).
Always verify the OE reference 03C127026P, 03C127026M, 03C127026J, HPP0005 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 03C127026R needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Golf Mk5/Mk6 / Scirocco / Tiguan | Volkswagen 1.4L TSI DOHC 16V Twincharger / Turbo EA111 (CAXA / CAVE / CAVD / CTHD / BLG / BMY) | 2006-2015 |
| Audi A1 (8X) / A3 (8P) | Volkswagen 1.4L TSI DOHC 16V Twincharger / Turbo EA111 (CAXA / CAVE / CAVD / CTHD / BLG / BMY) | 2007-2014 |
Technical Specifications
| Specification | Value |
|---|---|
| Operating PressureCore Spec | |
| Pump Technology | Single Plunger Mechanical Camshaft-Driven HPFP |
| Flow Control | Integrated Solenoid Metering Valve (N290) |
| Mounting Flange Torque | 20 N·m |
| High Pressure Line Torque | 27 N·m |
| Drive Type | Intake Camshaft Driven with Roller Tappet |
| Fuel Type | Gasoline / Petrol Direct Injection (TSI / TFSI / Twincharger) |
| OE Cross References | 03C127026R, 03C127026P, 03C127026M, 03C127026J, HPP0005 |
| Failure Symptoms | EPC warning lamp on acceleration, P0087 low rail pressure, hard starting, limp mode above 3000 RPM |
| Diagnostic Test | VCDS measuring block Group 106 & 140 (Specified vs Actual Rail Pressure under boost) |
Installation Tips
- Disconnect battery; pull fuel pump fuse and crank engine for 5 seconds to depressurize fuel lines.
- Disconnect electrical connector to N290 metering valve and unfasten low-pressure feed hose clamp.
- Counter-hold pump discharge union and loosen high-pressure steel tube flare nut using a flare wrench.
- Loosen the two M6 mounting bolts evenly in alternating turns to release internal spring tension evenly.
- Withdraw HPFP and inspect roller tappet in the cylinder head bore for flat spots or surface galling.
- Fit a new sealing O-ring lubricated with clean engine oil; seat pump into mounting bore.
- Tighten mounting flange bolts progressively in alternating steps to 20 N·m.
- Hand-thread high-pressure line flare nut until seated, then torque to 27 N·m; reconnect N290 connector.
- Cycle ignition several times to bleed air; start engine and inspect all joints for leaks.
- Confirm the engine code and vehicle application against the EPC before ordering this 03C127026R pump.
- Tighten the pump mounting/hold-down fasteners to 20 N·m.
- Tighten the high-pressure line to 27 N·m.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Volkswagen or Audi 1.4L TSI?
Part number 03C127026R is a gasoline direct-injection high-pressure fuel pump listed for 150 bar system pressure and the Volkswagen 1.4L TSI DOHC 16V Twincharger/Turbo EA111 family (CAXA / CAVE / CAVD / CTHD / BLG / BMY). It is listed for Volkswagen Golf Mk5/Mk6, Scirocco, Tiguan (2006-2015) and Audi A1 (8X)/A3 (8P) (2007-2014); confirm the exact engine code and vehicle application against the EPC before ordering.
What trouble codes point to a problem with this pump?
The verified diagnostic trouble codes listed for this application are P0300, P0087, P0193, P0089, and P0191. A specific symptom list is not stated here, so confirm the diagnosis against the vehicle's EPC instead of guessing.
Do I need coding/adaptation or new seals after installing this pump?
Coding/adaptation requirements and seal reuse are not stated in the verified facts, so they must be confirmed against the vehicle's EPC instead of guessing. The listed installation torques are 20 N·m for the mounting/hold-down and 27 N·m for the high-pressure line.
How can I verify the old pump part number before replacement?
Compare the old unit against 03C127026R and the listed cross references 03C127026P, 03C127026M, 03C127026J, HPP0005, and HM10018. If the number does not match, confirm fitment against the vehicle's EPC before proceeding.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.