HITACHI 06H127025Q
High Pressure Fuel Pump VW Golf GTI Passat Audi A4 A5 Q5 2.0 TSI EA888 Gen 1 2
06H127025E, 06H127025G, 06H127025K, 06H127025M, HPP0005INTEGRATED N276 FUEL PRESSURE REGULATING VALVE-150 bar peak rail pressureProduct Overview
The Hitachi 06H127025Q is a mechanical plunger direct injection fuel pump for Volkswagen and Audi EA888 Gen 1 and Gen 2 1.8L / 2.0L TSI / TFSI engines (CCTA / CAEB / CDNC). It is listed for the Golf VI GTI 2.0 TSI (2009-2013), Audi A4 B8 (2008-2015) and Q5 8R (2009-2015). A camshaft four-lobe drives the pump through roller tappet 06L109311 to a 150 bar (15 MPa / 2175 psi) system pressure. Mounting flange bolts are tightened evenly in a diagonal sequence to 20 N·m, the high-pressure line flare nut to 27 N·m and the low-pressure banjo bolt to 15 N·m. Common codes are P0087, P2293 and P0088. Replace roller tappet follower 06L109311 and lubricate the pump piston tip with clean engine oil before installation.
Always verify the OE reference 06H127025E, 06H127025G, 06H127025K, 06H127025M stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 06H127025Q needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Golf VI GTI 2.0 TSI | Volkswagen / Audi EA888 Gen 1 & Gen 2 (1.8L & 2.0L TSI / TFSI CCTA / CAEB / CDNC) | 2009-2013 |
| Audi A4 (B8) | Volkswagen / Audi EA888 Gen 1 & Gen 2 (1.8L & 2.0L TSI / TFSI CCTA / CAEB / CDNC) | 2008-2015 |
| Audi Q5 (8R) | Volkswagen / Audi EA888 Gen 1 & Gen 2 (1.8L & 2.0L TSI / TFSI CCTA / CAEB / CDNC) | 2009-2015 |
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Hitachi Mechanical Plunger Direct Injection Fuel Pump |
| Operating PressureCore Spec | |
| Actuation Mechanism | Camshaft 4-lobe driven via roller tappet 06L109311 |
| Mounting Flange Torque | 20 N·m (tightened evenly in diagonal sequence) |
| High Pressure Line Torque | 27 N·m Flare Nut Connection |
| Low Pressure Fitting Torque | 15 N·m banjo bolt connection |
| Common Fault Codes | P0087 (Fuel Rail Pressure Too Low), P2293 (Fuel Pressure Regulator 2 Performance), P0088 |
| Workshop Precaution | Always replace roller tappet follower 06L109311 and lubricate pump piston tip with clean engine oil before installation |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Relieve Rail Pressure & Disconnect Low Pressure Line: Depressurize fuel system using scan tool test function or fuse pull. Remove low-pressure spring clamp and detach rubber feed line.
- Detach High Pressure Steel Pipe: Loosen steel fuel line flare nut (27 N·m) while holding pump outlet fitting with counter-wrench to prevent adapter distortion.
- Remove Flange Screws & Inspect Roller Tappet 06L109311: Unscrew two M8 flange bolts evenly in alternating half-turns. Remove pump and withdraw roller tappet 06L109311. Check roller for flat spots or pin play.
- Install Pump, Torque Fasteners & Bleed Air: Lubricate new O-ring seal. Tighten mounting bolts diagonally to 20 N·m. Torque steel line to 27 N·m. Cycle ignition 3 times before starting engine.
- Torque the pump mounting/hold-down fasteners to 20 N·m.
- Torque the high-pressure line to 27 N·m.
- Confirm exact fitment against the vehicle EPC before ordering.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Volkswagen Golf VI GTI 2.0 TSI?
It is listed for the Volkswagen Golf VI GTI 2.0 TSI (2009–2013), Audi A4 (B8) (2008–2015), and Audi Q5 (8R) (2009–2015). It is also listed for Volkswagen/Audi EA888 Gen 1 & Gen 2 1.8L & 2.0L TSI/TFSI CCTA/CAEB/CDNC; confirm the exact vehicle application against the EPC before ordering.
What diagnostic trouble codes are associated with this pump?
The verified diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. The verified facts do not include a separate symptom list, so use the vehicle’s diagnostic procedure and confirm any additional diagnosis against service information.
What are the mounting and high-pressure line torque specs?
The mounting/hold-down torque is 20 N·m, and the high-pressure line torque is 27 N·m. This gasoline direct-injection high-pressure fuel pump is listed with a system pressure of 150 bar.
Do I need coding/adaptation or new seals, and how do I verify the old part?
Coding/adaptation and seal-reuse guidance are not included in the verified facts; confirm those points against the vehicle EPC or service information. To verify the old part, check for part number 06H127025Q and the listed cross references 06H127025E, 06H127025G, 06H127025K, 06H127025M, and HPP0005.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.