BOSCH 05E906036C
High Pressure Fuel Injector VW Golf Mk8 Tiguan Audi A3 1.5 TSI EA211 Evo 0261500585
05E906036Q, 05E906036F, 0261500585, 02615008105-HOLE LASER MICRO ORIFICE SOLENOID NOZZLE5-hole asymmetrical laser-drilled micro orifices optimized for Miller cycle350 bar peak rail pressureProduct Overview
The Bosch 05E906036C (Bosch 0261500585) is a Bosch HDEV6 350-bar ultra-high-pressure gasoline direct injector for Volkswagen and Audi EA211 Evo 1.5L TSI / TFSI engines. It is listed for the VW Golf Mk8 (2019-2024), Audi A3 8Y Sportback (2020-2024) and VW Tiguan II (2018-2024). It operates at a 350 bar (35 MPa / 5075 psi) rail pressure with 5-hole asymmetrical laser-drilled micro orifices optimized for the Miller cycle and an actuator resistance of 1.5-1.9 Ω at 20°C. Rail mounting bolts take 10 N·m and the high-pressure connecting pipe union 25 N·m. Common codes are P0171, P0300 and P0301-P0304. Carbon should be cleaned from the cylinder head injector bores before new Teflon combustion seals are fitted.
Always verify the OE reference 05E906036Q, 05E906036F stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 05E906036C needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Volkswagen Golf Mk8 | Volkswagen / Audi EA211 1.4L & 1.5L TSI / TFSI (CZDA / CZEA / CHPA / DADA) | 2019-2024 |
| Audi A3 8Y Sportback | Volkswagen / Audi EA211 1.4L & 1.5L TSI / TFSI (CZDA / CZEA / CHPA / DADA) | 2020-2024 |
| Volkswagen Tiguan II | Volkswagen / Audi EA211 1.4L & 1.5L TSI / TFSI (CZDA / CZEA / CHPA / DADA) | 2018-2024 |
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDEV6 350-bar Ultra-High-Pressure Gasoline Direct Injector |
| Operating PressureCore Spec | |
| Nozzle DesignCore Spec | |
| Fuel Rail Bolt Torque | 10 N·m (rail mounting bolts to cylinder head) |
| High Pressure Line Torque | 25 N·m (high pressure connecting pipe union) |
| Actuator Resistance | 1.5 - 1.9 Ω at 20°C (ultra-fast solenoid actuation) |
| Common Fault Codes | P0171 (System Too Lean Bank 1), P0300 (Random Misfire), P0301-P0304 (Cylinder Misfire) |
| Workshop Precaution | Clean carbon deposits from injector bores in cylinder head before fitting new Teflon combustion seals |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Release Fuel Rail Pressure & Disconnect Battery Negative: Depressurize 350-bar fuel system using VCDS/ODIS diagnostics or fuel pump fuse isolation. Unbolt intake manifold pressure pipe.
- Remove High Pressure Fuel Rail & Electrical Plugs: Disconnect electrical wiring connectors from each injector. Loosen the high pressure supply line flare nut (25 N·m) and remove fuel rail retaining bolts (10 N·m).
- Pull Injectors & Install Replacement Teflon Radial Seals: Extract injectors using puller kit T10133C. Clean carbon crust from combustion tip ports. Install new Teflon combustion chamber seal ring using assembly cone.
- Reinstall Rail Assembly & Torque Connections to Spec: Seat injectors square into cylinder head bores. Torque rail bolts evenly to 10 N·m. Tighten high pressure line union to 25 N·m. Perform leak check under high pressure.
- Tighten the injector hold-down to 10 N·m and the high-pressure line to 25 N·m.
- Verify the old unit’s markings against 05E906036C and the listed cross references 05E906036Q, 05E906036F, 0261500585, 0261500810, and 06H906036G before ordering.
- Confirm the vehicle application against the EPC before installation.
Frequently Asked Questions
Does part number 05E906036C fit a Volkswagen Golf Mk8, Audi A3 8Y Sportback, or Volkswagen Tiguan II with an EA211 1.4L/1.5L TSI/TFSI engine?
The listing covers Volkswagen/Audi EA211 1.4L & 1.5L TSI/TFSI engines CZDA/CZEA/CHPA/DADA. Listed fitment includes VW Golf Mk8 2019-2024, Audi A3 8Y Sportback 2020-2024, and VW Tiguan II 2018-2024. Confirm the exact vehicle application against the vehicle’s EPC before ordering.
What mounting and high-pressure line torques should I use for this injector?
Use 10 N·m for the injector mounting/hold-down torque. Use 25 N·m for the high-pressure line torque. The listed system pressure is 350 bar.
What diagnostic trouble codes are listed for this gasoline direct-injection injector?
The listed DTCs are P0300, P0301, P0302, P0304, and P0087. These are the only diagnostic trouble code references provided in the verified facts.
Do I need coding or adaptation after installing this injector, and can I reuse the seals?
Coding/adaptation requirements are not stated in the verified facts. Seal reuse requirements are also not stated. Confirm both against the vehicle’s EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.