BOSCH 06E906036AJ
Direct Fuel Injector Audi S4 S5 A6 A7 A8 Q7 SQ5 3.0 TFSI EA837 0261500160
06E906036K, 06E906036Q, 0261500160, FJ1021--150 bar peak rail pressureProduct Overview
The BOSCH 06E906036AJ is a factory precision fuel injection component engineered specifically for the Audi 3.0L TFSI Supercharged DOHC 24V V6 EA837 (CTUB / CGWA / CGWB / CREC). Manufactured to strict original equipment tolerances, it delivers precise fuel atomization and operates up to its rated pressure of 150 bar (2175 psi). Common operational failure symptoms that point directly to this assembly include: Persistent Diagnostic Trouble Codes such as P0300, P0301, P0302, P0172 stored in the ECM. Hard cold starting, erratic idle oscillations, and severe acceleration stumbling. Unburnt fuel smell in the exhaust, black tailpipe soot, or fuel dilution in the engine crankcase. Loss of high-RPM power and engine protection limp-mode activation under highway load.
Always verify the OE reference 06E906036K, 06E906036Q, FJ1021 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 06E906036AJ needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| sku | 06E906036AJ |
| brand | BOSCH |
| manufacturer_code | 0261500160 |
| pressure_rating | 150 bar (2175 psi) |
| torque_flange | 9 N-m (80 lb-in) |
| torque_line | 9 N-m (80 lb-in) |
| engine_family | Audi 3.0L TFSI Supercharged DOHC 24V V6 EA837 (CTUB / CGWA / CGWB / CREC) |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Always replace single-use high-pressure fuel lines and Teflon/copper sealing washers before installation.
- Lubricate the pump roller tappet or injector O-rings with clean engine oil before guiding into place.
- Tighten mounting flange fasteners in an even criss-cross pattern to 9 N-m (80 lb-in).
- Hand-thread fuel rail fittings first, then torque high-pressure flare nuts to 9 N-m (80 lb-in) using a calibrated crowfoot wrench.
- Cycle the low-pressure fuel pump multiple times and perform a physical leak inspection before engine ignition.
- Verify the engine code and part number 06E906036AJ against the vehicle EPC before installation.
- Tighten the injector mounting/hold-down and high-pressure line to 9 N·m.
- Do not assume coding, adaptation, or seal reuse; confirm those details against the vehicle's EPC.
Frequently Asked Questions
Will this injector fit my Audi or Porsche?
This injector is listed for Audi/VW/Porsche EA837 3.0L V6 Supercharged TFSI engines with CGWB, CTUB, or CREC, including Audi S4/S5 B8/B8.5 2010-2017, Audi A6 C7/A7 4G8 2012-2018, Audi Q7 4L/SQ5 8R 2011-2017, and Porsche Cayenne/Panamera 2011-2018. Confirm the exact vehicle, engine code, and part number against its EPC before ordering.
What diagnostic trouble codes should I check if I suspect this injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. Use these codes with vehicle service information to confirm the fault path; the listing does not provide additional symptom or service-life details.
What are the mounting and high-pressure line torque values, and what system pressure is listed?
The mounting/hold-down torque is 9 N·m, and the high-pressure line torque is 9 N·m. The listed system pressure is 150 bar.
How do I verify the old injector and cross-reference before replacement?
Check the old unit for 06E906036AJ and compare the listed cross references: 06E906036AJ, 06E906036K, 06E906036Q, 0261500160, FJ1021, and 0261500055. Coding/adaptation, seal reuse, and expected service life are not stated here; confirm them against the vehicle's EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.