HITACHI 06E127025G
High Pressure Fuel Pump Audi S4 S5 A6 A7 A8 Q7 SQ5 3.0T Supercharged EA837 HPP0007
06E127025N, 06E127025AB, 06E127025J, HPP0007, HM10017, FI1534INTEGRATED FUEL METERING SOLENOID VALVE N290-200 bar peak rail pressureProduct Overview
The Hitachi 06E127025G (aftermarket reference HPP0007, superseding part numbers 06E127025N, 06E127025AB, and 06E127025J) is the authentic original equipment high-pressure mechanical fuel pump engineered for Audi's celebrated 3.0-liter supercharged V6 TFSI engine family (EA837). Generating up to 200 bar (2,900 psi) of regulated direct injection fuel pressure, this cam-driven single-plunger pump powers high-performance executive vehicles including the Audi S4 (B8/B8.5 2010-2016), S5 (2010-2017), A6 C7 (2012-2018), A7 (2012-2018), Q7 3.0T (2011-2015), SQ5 (2014-2017), and select Porsche Cayenne and Panamera models.
Always verify the original manufacturer reference stamped on your component before ordering. For 06E127025G, inspect matching OE cross-references and ensure related high-pressure seals, followers, or grommets are renewed during service.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Hitachi / Audi FSI 200-Bar High Pressure Direct Injection |
| Maximum Operating Fuel Pressure | 200 bar (2,900 psi / 20.0 MPa regulated system pressure) |
| Pump Drive Configuration | Tri-Lobe Camshaft Follower Driven via Hardened Roller Tappet |
| Quantity Control Solenoid | Integrated Electronic Fuel Metering Valve (N290 PWM Modulated) |
| Pump Mounting Flange Torque | 20 N·m (15 lb-ft) tightened evenly in criss-cross stages |
| High-Pressure Flare Nut Tube Torque | 27 N·m (20 lb-ft) rigid stainless steel delivery pipe |
| Low-Pressure Supply Line Torque | Banjo fitting 15 N·m / Quick-connect click retention |
| Internal Piston Seals Architecture | Multi-Lip Dynamic Fluorocarbon Piston Seal with Fuel Scavenge Port |
| Manufacturer | Hitachi Astemo, Ltd. (Tier-1 OEM for Audi AG & Volkswagen Group) |
| Production Reference | Hitachi HPP0007 / Audi OE 06E 127 025 G |
| Operating PressureCore Spec |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Low & High Pressure Fuel System Depressurization: Pull 15A low-pressure fuel pump fuse from passenger dashboard fuse block. Start engine and let it run until it stalls from fuel depletion, then disconnect negative battery cable.
- Intake Ducting & Supercharger Area Clearance: Disconnect mass air flow sensor wiring and remove intake bellows ducting. Clear access to the rear driver-side cylinder head where the mechanical HPFP resides.
- N290 Solenoid Harness & Fuel Lines Disconnection: Unclip wiring plug from the N290 fuel metering valve. Crack open high-pressure flared fitting slowly with a 17mm flare nut wrench while wrapping a shop towel around the union.
- Flange Fasteners Removal & Roller Tappet Inspection: Back out mounting bolts in alternating half-turns to release internal plunger spring load squarely. Extract pump and inspect internal roller cam follower for surface spalling or binding.
- O-Ring Lubrication, Installation & Sequence Torquing: Coat new Viton housing O-ring and roller tappet with fresh synthetic engine oil. Seat pump into bore and torque flange bolts evenly to 20 N·m (15 lb-ft). Torque high-pressure pipe flare nut to 27 N·m (20 lb-ft).
- Before fitting 06E127025G, confirm the vehicle application and original pump identification against the EPC to avoid a wrong replacement.
- Work cleanly around the high-pressure fuel system and follow the manufacturer's workshop procedure for release, replacement and any required matching.
- After installation, verify the repair with the vehicle's specified diagnostic and fuel-system test plan rather than relying on a visual check alone.
Frequently Asked Questions
Which vehicles is 06E127025G listed for?
06E127025G is listed for Audi, Volkswagen and Porsche supercharged TFSI applications in this engine family. Confirm your exact vehicle by VIN and against the EPC before ordering.
What are common symptoms of a failed high-pressure fuel pump?
Specific failure symptoms are not stated in the supplied data. Diagnose high-pressure fuel delivery with the vehicle's workshop test plan and confirm fault codes and pressure checks against the manual.
What should I check before ordering this pump?
Check the VIN, engine code and original pump identification against the EPC, then verify the listed Audi, Volkswagen or Porsche application. Confirm that 06E127025G is correct for your vehicle.
Does the old unit need coding or adaptation?
Coding or adaptation requirements are not stated in the supplied data. Confirm the matching or adaptation procedure against the vehicle's EPC or workshop manual before installation; do not assume plug-and-play operation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.