HITACHI 06E127025AB
High Pressure Fuel Pump Audi S4 S5 A6 C7 A7 A8 Q7 3.0T V6 EA837 Supercharged
06E127025AC, 0261520228, HPP0012--150 bar peak rail pressureProduct Overview
The 06E127025AB is an original equipment (HITACHI) precision component engineered specifically for the Audi 3.0L TFSI Supercharged DOHC 24V V6 (EA837 / CTUB / CGWB). Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference 06E127025AC, HPP0012 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 06E127025AB needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 06E127025AB |
| Manufacturer Brand | HITACHI |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Audi 3.0L TFSI Supercharged DOHC 24V V6 (EA837 / CTUB / CGWB) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 20 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 25 N-m (18 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (15 lb-ft), and torque fuel line fittings to 25 N-m (18 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the engine code and part number against the vehicle's EPC before installation.
- Tighten the mounting/hold-down to 20 N·m and the high-pressure line to 25 N·m.
- Confirm coding/adaptation and seal-reuse requirements in the service information before installation.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Audi or Porsche?
It is a gasoline direct-injection high-pressure fuel pump listed for the Audi/VW/Porsche EA837 3.0L V6 Supercharged TFSI engine family with CGWB, CTUB, or CREC engine codes. Fitment includes Audi S4/S5 B8/B8.5 2010-2017, Audi A6 C7/A7 4G8 2012-2018, Audi Q7 4L/SQ5 8R 2011-2017, and Porsche Cayenne/Panamera 2011-2018. Confirm the part number and engine code against the vehicle's EPC before ordering.
What are the mounting and high-pressure line torque specs?
The mounting/hold-down torque is 20 N·m, and the high-pressure line torque is 25 N·m. The listed system pressure is 150 bar.
Which diagnostic trouble codes are listed for this pump?
The listed DTCs are P0300, P0087, P0193, P0089, and P0191. The verified facts do not list specific symptoms or a diagnostic procedure, so confirm diagnosis with the vehicle's service information.
How can I verify the old pump part number and cross references?
The primary part number is 06E127025AB, and the listed cross references are 06E127025AB, 06E127025AC, 0261520228, HPP0012, 06E906036E, and 06E906036AJ. Confirm the number on the old pump and against the vehicle's EPC before ordering.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.