HITACHI 06M127025F
High Pressure Fuel Pump Audi S4 S5 SQ5 B9 A8 D5 Porsche Macan S 3.0T EA839 HPP0047
06M127025B, HPP0047, GDP225--250 bar peak rail pressureProduct Overview
The 06M127025F is an original equipment (HITACHI) precision component engineered specifically for the Audi / Porsche 3.0L Turbocharged DOHC 24V V6 TFSI EA839 (CWGD / CZSE / DLZA). Operating at peak injection pressures up to 250 bar (3625 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P2293, P053F.
Always verify the OE reference 06M127025B, HPP0047, GDP225 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 06M127025F needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 06M127025F |
| Manufacturer Brand | HITACHI |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Audi / Porsche 3.0L Turbocharged DOHC 24V V6 TFSI EA839 (CWGD / CZSE / DLZA) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 20 N-m (177 lb-in) |
| Fuel Line / Rail Torque | 27 N-m (20 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P2293, P053F |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (177 lb-in), and torque fuel line fittings to 27 N-m (20 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm fitment by VIN/EPC for EA839 CWGD/DECA applications before installing the pump.
- Torque the mounting/hold-down fasteners to 20 N·m.
- Torque the high-pressure line to 27 N·m.
Frequently Asked Questions
Will this pump fit my Porsche Macan or Audi S4/S5/RS4/RS5?
Part number 06M127025F is a gasoline direct-injection high-pressure fuel pump for the Audi/Porsche EA839 family (2.9L BiTurbo & 3.0L V6 Turbo TFSI CWGD/DECA). Listed fitment is Porsche Macan CWGD/DECA 2019-2023, Audi S4/S5 B9 CWGD/DECA 2017-2023, and Audi RS4/RS5 B9 CWGD/DECA 2018-2023. Cross references listed are 06M127025F, 06M127025B, HPP0047, GDP225, and 06M127025G. Confirm by VIN/EPC before ordering.
Which diagnostic trouble codes are listed for this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. The verified facts do not include symptom descriptions, so confirm the actual fault against the vehicle’s EPC instead of guessing.
What are the mounting/hold-down and high-pressure line torque specifications?
Mounting/hold-down torque is 20 N·m. High-pressure line torque is 27 N·m. System pressure is 250 bar.
Does this pump require coding/adaptation, and can I reuse the seals?
Coding/adaptation requirements and seal-reuse guidance are not stated in the verified facts, so confirm them against the vehicle’s EPC instead of guessing. Expected service life is also not stated; confirm any service-life or replacement interval against the vehicle’s EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.