BOSCH 9A712702500
High Pressure Fuel Pump Porsche Macan Cayenne Panamera Audi S4 S5 3.0T EA839 0261520472
9A712702502, 06M127025Q, 06M127025R, 0261520473, GDP216, 0261520472--250 bar peak rail pressureProduct Overview
The 9A712702500 is an original equipment (BOSCH) precision component engineered specifically for the Porsche-Audi 2.9L / 3.0L Turbo DOHC 24V V6 (EA839 / CWGD / DECA). Operating at peak injection pressures up to 250 bar (3625 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference 9A712702502, 06M127025Q, 06M127025R, GDP216 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 9A712702500 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 9A712702500 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Porsche-Audi 2.9L / 3.0L Turbo DOHC 24V V6 (EA839 / CWGD / DECA) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 20 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 28 N-m (21 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (15 lb-ft), and torque fuel line fittings to 28 N-m (21 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Tighten the pump mounting/hold-down to 20 N·m.
- Tighten the high-pressure fuel line to 28 N·m.
- Confirm the old pump part number and listed cross-references against the vehicle's EPC before ordering.
Frequently Asked Questions
Which vehicles and engine families does this pump fit?
This gasoline direct-injection high-pressure fuel pump is listed for the Audi/Porsche EA839 engine family (2.9L BiTurbo & 3.0L V6 Turbo TFSI CWGD / DECA) and is rated at 250 bar. Listed fitment includes Porsche Macan CWGD/DECA (2019-2023), Audi S4/S5 B9 CWGD/DECA (2017-2023), and Audi RS4/RS5 B9 CWGD/DECA (2018-2023). Confirm any application not listed against the vehicle's EPC.
What DTCs or symptoms point to this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. The provided facts do not list specific symptoms beyond these DTCs, so confirm diagnosis against the vehicle's EPC or service information.
Do I need coding or adaptation, and can I reuse the seals?
The provided facts do not state coding/adaptation requirements or seal-reuse guidance for this pump. Confirm both against the vehicle's EPC before installation.
How do I verify the old pump and what torque values should I use?
Verify the old unit by part number 9A712702500 and the listed cross-references: 9A712702502, 06M127025Q, 06M127025R, 0261520473, and GDP216. The mounting/hold-down torque is 20 N·m, and the high-pressure line torque is 28 N·m.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.