BOSCH 35320-2G720
High Pressure Fuel Pump Hyundai Sonata Santa Fe Kia Optima Sorento 2.4L GDI 2.0T
35320-2G730, 35320-2G700, 0261520282INTEGRATED NORMALLY OPEN 12V PULSE-WIDTH MODULATED SCV-150 bar peak rail pressureProduct Overview
The Bosch 35320-2G720 is a Bosch HDP5 radial mechanical plunger high-pressure fuel pump for Hyundai and Kia 2.0L T-GDI and 2.4L GDI Theta II engines (G4KH / G4KJ). It is listed for the Sonata 2.4L GDI (2011-2019), Kia Optima K5 2.4L GDI (2011-2020) and Santa Fe Sport 2.4L GDI (2013-2018). An exhaust camshaft lobe drives the pump through roller tappet lifter 35325-2G700 to 150 bar (15 MPa / 2175 psi); the integrated normally-open 12V PWM suction control valve regulates delivery. Flange bolts are tightened evenly in a cross pattern to 13 N·m and the high-pressure line flare nut to 27 N·m. Common codes are P0087, P0088 and P0172. Inspect the cam roller follower for scoring and check for fuel-diluted oil from a torn plunger seal.
Always verify the OE reference 353202G730, 353202G700 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 35320-2G720 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Bosch HDP-5 Radial Mechanical Plunger High-Pressure Fuel Pump |
| Operating PressureCore Spec | |
| Actuation Mechanism | Exhaust Camshaft Lobe via Roller Tappet Lifter 35325-2G700 |
| Mounting Flange Torque | 13 N·m Evenly tightened cross pattern |
| High Pressure Line Torque | 27 N·m Flare Nut Connection |
| Pressure Regulator Valve | Integrated Normally Open 12V Pulse-Width Modulated SCV |
| Common Fault Codes | P0087 (Fuel Rail Pressure Too Low), P0088 (Rail Pressure Too High), P0172 (Fuel Trim Rich) |
| Workshop Precaution | Inspect cam roller follower 35325-2G700 for scoring; verify oil is not fuel-diluted from torn plunger seal |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel Rail & Disconnect Wiring: Depressurize fuel line by removing fuel pump fuse. Disconnect electrical connector from high pressure flow control solenoid.
- Disconnect Fuel Feed & High Pressure Pipes: Remove low pressure rubber supply line clamp. Loosen high-pressure flared fuel pipe connection (27 N·m union nut).
- Remove Flange Bolts & Inspect Roller Tappet: Back out mounting flange bolts evenly in alternating turns. Remove pump body and extract roller lifter 35325-2G700. Check for surface galling.
- Install Pump with New O-Ring & Final Torque: Install new lubricated Viton seal ring. Position pump squarely and torque flange bolts evenly to 13 N·m. Torque high pressure steel pipe to 27 N·m.
- Confirm the pump is part number 35320-2G720 or a listed cross reference before installation.
- Tighten the mounting / hold-down to 13 N·m and the high-pressure line to 27 N·m.
- Check fitment against the EPC for the listed Theta II G4KH / G4KJ applications before ordering.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Hyundai or Kia, and how do I verify the old part?
It is listed for the Hyundai/Kia 2.0L T-GDI & 2.4L GDI Theta II (G4KH / G4KJ) engine family, with fitment for Hyundai Sonata 2.4L GDI 2011-2019, Kia Optima K5 2.4L GDI 2011-2020, and Hyundai Santa Fe Sport 2.4L GDI 2013-2018. Verify the old pump by matching part number 35320-2G720 or cross references 353202G720, 353202G730, 353202G700, 0261520282, 0261520215, or 1679059B004. For any application not listed, confirm against the vehicle's EPC.
What symptoms or trouble codes point to a failed high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. Use these codes as diagnostic clues and confirm the fault before replacing the pump; the supplied facts do not describe specific symptom behavior.
What are the installation torque specs for this pump?
Mounting / hold-down torque is 13 N·m, and the high-pressure line torque is 27 N·m. The system pressure is 150 bar. Follow the vehicle service procedure for the GDI high-pressure fuel pump installation.
Does this pump require coding/adaptation, can the seals be reused, and what service life should I expect?
Coding/adaptation, seal reuse, and expected service life are not stated in the supplied facts. Confirm these points against the vehicle's EPC or service information instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.