BOSCH 16600-9HP0A
High Pressure Fuel Injector Nissan Altima Rogue Murano Pathfinder 2.5L 3.5L GDI
0261500073, 0261500074, 16600-6CA0ALASER MULTI-DRILLED SPRAY PATTERN ATOMIZER TIP-150 bar peak rail pressureProduct Overview
The 16600-9HP0A is an industrial-grade genuine Tier-1 replacement engineered for Nissan 2.5L QR25DD I4 / 3.5L VQ35DD V6 Gasoline Direct Injection Engines. Designed for high-precision Nissan Direct Ignition & Gasoline Direct Injection (DIG), it delivers factory calibration standards, OE cross-reference compatibility, and verified workshop reliability.
Always verify the OE reference 166006CA0A stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16600-9HP0A needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Nissan Altima 2.5L | Nissan 2.0L & 2.5L Direct & Port Injection (MR20DD / QR25DE / QR25DD / PR25DD) | 2019-2024 |
| Nissan Pathfinder 3.5L V6 | Nissan 2.0L & 2.5L Direct & Port Injection (MR20DD / QR25DE / QR25DD / PR25DD) | 2017-2024 |
| Infiniti QX60 3.5L V6 | Nissan 2.0L & 2.5L Direct & Port Injection (MR20DD / QR25DE / QR25DD / PR25DD) | 2017-2024 |
Technical Specifications
| Specification | Value |
|---|---|
| Operating Principle | Bosch High-Pressure Solenoid Electromagnetic Actuation |
| Fuel Delivery Pressure | Up to 150 bar (15 MPa / 2175 psi) |
| Coil Electrical Resistance | 1.3 - 1.7 Ohm at 20°C |
| Rail Retaining Bolt Torque | 21 N·m M8 Thread Fasteners |
| High Pressure Pipe Torque | 30 N·m High-Pressure Tube Fitting |
| Combustion Chamber Seal | PTFE Virgin Teflon Radial Ring with backup buffer |
| Associated Fault Codes | P0171 (Lean Bank 1), P0174 (Lean Bank 2), P0300-P0306 (Random Misfire) |
| Primary Diagnostic Check | Check LTFT/STFT fuel trims under high load; clogged nozzle causes severe lean spike |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Relieve Residual Rail Pressure: Disconnect low pressure electric pump fuse. Crank engine 5-10 seconds to dissipate remaining fuel pressure in the high-pressure rail.
- Clean Injector Bores & Remove Old Seals: Clean bore thoroughly down to cylinder head seat. Never use metal picks that could scratch internal precision sealing walls.
- Compress Teflon Seals using Calibration Cone: Fit brand new Teflon combustion seal using mounting sleeve. Compress ring in step-down calibration die until outer diameter fits cleanly.
- Position Fuel Rail & Torque Bolts: Guide fuel rail assembly squarely into cylinder head ports. Tighten rail bolts evenly in two steps up to final torque of 21 N·m.
- Attach High Pressure Line & Verify Leakage: Thread high pressure feed line flare nut finger tight, then tighten to 30 N·m. Start engine and verify zero fuel misting or weeping.
- Depressurize the 150 bar fuel system before servicing the gasoline direct-injection injector.
- Tighten the injector mounting/hold-down to 21 N·m.
- Tighten the high-pressure line to 30 N·m.
Frequently Asked Questions
What causes P0171 and P0174 codes on Nissan VQ35DD engines?
Direct injection nozzles operate directly in the combustion chamber. Carbon buildup on the precision laser-drilled orifices restricts fuel volume, leaning out fuel mixture and triggering P0171 (Bank 1) and P0174 (Bank 2) under highway acceleration.
Can I replace just one injector on a V6 VQ35DD engine?
While replacing a single failing injector is mechanically possible, injectors on the same cylinder bank share identical thermal and carbon cycles. Technicians strongly recommend replacing in bank sets to ensure balanced cylinder contribution.
What are the torque specifications for rail and pipe?
Fuel rail bracket mounting bolts must be torqued to 21 N·m. The high pressure fuel supply pipe flare nut requires 30 N·m.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.