HITACHI 16630-4CL0A
High Pressure Fuel Pump Nissan X Trail Rogue Altima 2.5L QR25DD 2.0L MR20DD HPP0021
16630-4CL0B, HPP0021, GDP506, HM10046--200 bar peak rail pressureProduct Overview
The 16630-4CL0A is an original equipment (HITACHI) precision component engineered specifically for the Nissan 2.5L DOHC 16V Direct Injection I4 (QR25DD) & 2.0L Direct Injection (MR20DD). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference 166304CL0B, HPP0021, GDP506, HM10046 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 16630-4CL0A needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16630-4CL0A |
| Manufacturer Brand | HITACHI |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Nissan 2.5L DOHC 16V Direct Injection I4 (QR25DD) & 2.0L Direct Injection (MR20DD) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 11 N-m (97 lb-in) |
| Fuel Line / Rail Torque | 28 N-m (21 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 11 N-m (97 lb-in), and torque fuel line fittings to 28 N-m (21 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the part number 16630-4CL0A and the vehicle fitment against the EPC before ordering.
- Tighten the mounting/hold-down fasteners to 11 N·m.
- Tighten the high-pressure line to 28 N·m.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Nissan X-Trail, Qashqai, or Rogue Sport?
This gasoline direct-injection high-pressure fuel pump is listed for Nissan X-Trail T32 with 2.0L MR20DD and 2.5L QR25DD (2014-2021), Qashqai J11 with 2.0L MR20DD (2014-2021), and Rogue Sport with 2.0L MR20DD (2017-2022). It is also listed for the Nissan 2.0L & 2.5L Direct & Port Injection engine family (MR20DD / QR25DE / QR25DD / PR25DD). Confirm final fitment against the vehicle’s EPC.
What fault codes are listed for this high-pressure fuel pump?
The diagnostic trouble codes listed for this part are P0300, P0087, P0193, P0089, and P0191. Specific symptom-to-code mapping and additional diagnosis are not stated here, so confirm them against the vehicle’s EPC or service information before replacing the pump.
Does this high-pressure fuel pump require coding or adaptation after installation?
Coding or adaptation requirements are not stated in the supplied facts. Confirm the required procedure against the vehicle’s EPC or service information instead of guessing.
How can I verify the old high-pressure fuel pump before ordering a replacement?
Check the old pump’s part number against 16630-4CL0A and the listed cross references: 166304CL0A, 166304CL0B, HPP0021, GDP506, HM10046, and 166001KT0A. If the marking is unclear or does not match, confirm the correct part against the vehicle’s EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.