Catalog / CONTINENTAL / A2C59513484
CONTINENTAL

Continental VDO A2C59513484

View Specs
SolenoidContinental / VDO Common RailEuro 5

Piezo Common Rail Injector

Reference data for CONTINENTAL A2C59513484 common rail injector · OEM 166008052R, H8200704191, 16600-00Q1V · Application 1.5 dCi, K9K 836, K9K 837, K9K 846
OE REFERENCE166008052R, H8200704191, 16600-00Q1V
CONTROL VALVE-
NOZZLEM0008P155
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Continental Siemens VDO A2C59513484 is an authentic piezoelectric common rail diesel injector calibrated for Renault Megane III (BZ0_) and 1.5 dCi engine platforms. Operating at an engineered rail pressure of 1600 bar, this piezo assembly features ultra-fast crystal actuation and precision multi-hole injection. Mandatory ECU calibration requires programming the 6-hex IIC calibration code into the engine control unit.

Before You Order

Verify VDO 6-Hex IIC calibration code and OEM cross reference before installation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Renault Megane III (BZ0_)1.5 dCi (K9K 836)2008-2015
Renault Scenic III (JZ0/1_)1.5 dCi (K9K 836)2009-2016
Nissan Qashqai / Qashqai +2 I (J10)1.5 dCi (K9K 430)2008-2013
Dacia Duster I (HS_)1.5 dCi (K9K 896)2010-2018
04

Technical Specifications

SpecificationValue
SKUA2C59513484
BrandCONTINENTAL
Fuel SystemContinental / VDO Common Rail
Operating PressureCore Spec
Hold Down Torque28 N·m
High-Pressure Line Torque28 N·m
Coding RequiredVDO 6-Hex IIC
Emission StandardEuro 5
Injector TypePiezoelectric
05

Installation Tips

  1. Depressurize And Isolate: Depressurize the fuel system and isolate it from all energy sources before opening any high-pressure connection; wait until the system is fully depressurized and secure the work area against accidental start-up.
  2. Clean And Disconnect: Clean the surrounding area of the cylinder head and injector bore before work, then disconnect the electrical connector and the spill/leak-off connections from the injector; keep removed connections clean and protected.
  3. Remove High-Pressure Line: Remove the high-pressure line from the injector and cap or protect the line and injector ports immediately to prevent dirt ingress; do not bend or stress the line during removal.
  4. Extract Old Injector: Release the hold-down and extract the old unit without twisting it; keep the piezo injector straight because it is bending-sensitive, and check the injector seat before fitting the replacement, following the manufacturer's service information for any additional sealing or damping components.
  5. Clean Bore And Fit Seals: Clean the injector bore and seat carefully, remove all residue without damaging sealing surfaces, fit new seals, and seat the unit straight in the bore, following the manufacturer's service information for component orientation.
  6. Tighten Hold-Down And Reconnect Line: Tighten the hold-down to 28 N·m, then reconnect the high-pressure line to the injector and tighten the line fitting to 28 N·m; keep the line aligned and free from side load.
  7. Calibration Coding: Record the VDO 6-Hex IIC calibration code and program it with a compatible diagnostic tool.
  8. Leak-Check And Start-Up: After coding, run the engine through a leak-check procedure and inspect all high-pressure connections and the injector seat for leaks; correct any leak before start-up, then start the engine and confirm smooth operation.
Tips & Warnings:
  • Before fitting, confirm the exact engine variant and injector application against the vehicle's EPC or workshop data.
  • Handle the injector and fuel system with cleanliness, and replace any seals or hardware only as specified by the vehicle manufacturer.
  • After installation, follow the workshop manual's diagnostic and adaptation procedure rather than assuming the unit is plug-and-play.
06

Frequently Asked Questions

QWhich vehicles does this injector fit?

It is listed for Renault Megane and Scenic, Nissan Qashqai, and Dacia Duster diesel applications; confirm the exact engine variant against the vehicle's EPC or workshop data before ordering.

QWhat are the symptoms of a failed unit?

Symptoms of a failed unit are not stated here; diagnose the vehicle using the manufacturer's procedure and confirm repair requirements against the vehicle's EPC or workshop manual before ordering.

QWhat should I check before ordering A2C59513484?

Confirm the vehicle's exact engine variant and injector application against the EPC or workshop data, inspect the connector and fuel system, and verify the required part before ordering A2C59513484.

QMust the replacement injector be coded or adapted after installation?

Coding or adaptation requirements are not stated here; confirm them against the vehicle's EPC or workshop manual before installation, and follow the manufacturer's diagnostic procedure for the injector replacement.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

P0300High

Random or Multiple Cylinder Misfire Detected

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

CRDI WORKSHOP ENGINEERING & DIAGNOSTICS

Piezo Injector 10 Bar Backleak & Stalling Guide

Bosch CRI3 piezo injector 10 bar backleak pressure guide. Diagnose hydraulic coupler cavitation, overflow valve failure, return line stalling & P0087.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol