Catalog / DELPHI / 28232248
DELPHI

Delphi 28232248

View Specs
SolenoidDelphi Common Rail SystemEuro 5

common rail injector

Reference data for DELPHI 28232248 common rail injector · OEM 166006212R, H8200704191, 16600-00Q1M · Application K9K, K9K 612, K9K 636
OE REFERENCE166006212R, H8200704191, 16600-00Q1M
CONTROL VALVE28239294
NOZZLEG374
EMISSIONEuro 5
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Delphi 28232248 is an authentic common rail diesel injector calibrated for Dacia Duster II and K9K engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and G374 nozzle. Mandatory ECU calibration requires programming the cylinder-specific C3i 20-digit code into the engine control unit to establish smooth delivery balance and Euro 5 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.

Before You Order

Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Dacia Duster II1.5 dCi (K9K 612)2013-2018
Renault Clio IV1.5 dCi (K9K 636)2012-2019
Nissan Note (E12)1.5 dCi (K9K 612)2013-2018
04

Technical Specifications

SpecificationValue
SKU28232248
BrandDELPHI
Fuel SystemCommon Rail (Delphi DFI)
Operating PressureCore Spec
Control ValveCore Spec
🔗 Shared Valve (40 assemblies):28232241282322422823638228236383
Nozzle CodeCore Spec
🔗 Shared Nozzle (7 assemblies):28231014282322412823638328337917
Hold Down Torque30 N·m
High-Pressure Line Torque28 N·m
Coding RequiredYes
Emission StandardEuro 5
05

Installation Tips

  1. Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
  2. Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
  3. Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
  4. Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
  5. Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
  6. Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 30 N·m, then reconnect the high-pressure line and tighten it to 28 N·m; reconnect the electrical connector and spill connection.
  7. Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
  8. Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
Tips & Warnings:
  • Confirm part number 28232248 and the listed cross references before fitting.
  • Tighten the mounting/hold-down to 30 N·m and the high-pressure line to 28 N·m.
  • Check for diagnostic trouble codes P0300, P0301, P0087, P0201 and P0204 before replacing the injector.
06

Frequently Asked Questions

QWill this common-rail diesel injector fit my Dacia Duster II 1.5 dCi?

It is listed for Dacia Duster II 1.5 dCi (K9K 612) from 2013 to 2018. It is also listed for Renault Clio IV 1.5 dCi (K9K 636) 2012-2019 and Nissan Note (E12) 1.5 dCi (K9K 612) 2013-2018. Confirm the exact application against your vehicle's EPC before ordering.

QWhich diagnostic trouble codes can point to this injector?

The listed diagnostic trouble codes are P0300, P0301, P0087, P0201 and P0204. Other symptom information is not stated, so confirm the diagnosis against the vehicle's EPC before replacing the injector.

QDoes this injector need coding or adaptation after installation?

Coding/adaptation requirements are not stated in the supplied facts, so confirm them against the vehicle's EPC instead of guessing. The listing only confirms the part number and listed fitment.

QHow can I verify the old injector before replacing it?

Check the old unit's part number and compare it with 28232248 and the listed cross references: 28232251, 166006212R, H8200704191 and 16600-00Q1M. Confirm the engine family is K9K, K9K 612 or K9K 636 and verify the application against the vehicle's EPC. If the number cannot be confirmed, check against the vehicle's EPC.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

P0300High

Random or Multiple Cylinder Misfire Detected

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol