Delphi EJBR01201Z
common rail injector
1219725, 2C1Q-9K546-AB, 123180428239294L095PBD1600 bar peak rail pressureProduct Overview
The Delphi EJBR01201Z is an authentic common rail diesel injector calibrated for Ford Transit IV and Puma 2.0 TDCi engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and L095PBD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 3 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR01201Z |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 50 N·m |
| High-Pressure Line Torque | 47 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 3 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 50 N·m, then reconnect the high-pressure line and tighten it to 47 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Confirm EJBR01201Z and the listed cross references before fitting.
- Tighten the mounting/hold-down to 50 N·m and the high-pressure line to 47 N·m.
- Check the listed DTCs P0300, P0087, P0201, P0204, and P0202 during diagnosis.
Frequently Asked Questions
Will this injector fit my Ford Transit or Mondeo, and how do I verify the old part?
EJBR01201Z is a common-rail diesel injector for the Puma 2.0 TDCi (FIFA) engine family. It is listed for Ford Transit IV 2.0 TDCi (FIFA) 2002-2006 and Ford Mondeo III 2.0 TDCi (FIFA) 2001-2007. Check the old unit against EJBR01201Z and cross references EJBR01601Z, 1219725, 2C1Q-9K546-AB, and 1231804; if markings do not match, confirm against the vehicle's EPC.
What symptoms or fault codes point to a failed injector?
The diagnostic trouble codes listed for this injector are P0300, P0087, P0201, P0204, and P0202. Use these codes as diagnostic evidence; the verified facts do not specify a single symptom pattern.
Does this injector need coding or adaptation after installation?
Coding/adaptation requirements are not stated in the verified facts. Confirm the correct procedure against the vehicle's EPC before installation.
What are the mounting and high-pressure line torque settings?
Mounting/hold-down torque is 50 N·m, and high-pressure line torque is 47 N·m. The injector is rated for a system pressure of 1600 bar.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.