Catalog / DELPHI / EJBR00801Z
DELPHI

Delphi EJBR00801Z

View Specs
SolenoidDelphi Common Rail SystemEuro 3

common rail injector

Reference data for DELPHI EJBR00801Z common rail injector · OEM 1141218, 2S7Q-9K546-AF, 1307096, 2S7Q-9K546-AH · Application Puma 2.0 TDCi, HJBC, HJBB
OE REFERENCE1141218, 2S7Q-9K546-AF, 1307096, 2S7Q-9K546-AH
CONTROL VALVE28239294
NOZZLEL093PBD
EMISSIONEuro 3
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Delphi EJBR00801Z is an authentic common rail diesel injector calibrated for Ford Mondeo III and Puma 2.0 TDCi engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and L093PBD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 3 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.

Before You Order

Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Ford Mondeo III2.0 TDCi (HJBC)2001-2007
Ford Transit IV2.0 TDCi (F3FA)2002-2006
04

Technical Specifications

SpecificationValue
SKUEJBR00801Z
BrandDELPHI
Fuel SystemCommon Rail (Delphi DFI)
Operating PressureCore Spec
Control ValveCore Spec
🔗 Shared Valve (40 assemblies):2823638328337917EJBR01101ZEJBR01201Z
Nozzle CodeCore Spec
Hold Down Torque50 N·m
High-Pressure Line Torque47 N·m
Coding RequiredYes
Emission StandardEuro 3
05

Installation Tips

  1. Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
  2. Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
  3. Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
  4. Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
  5. Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
  6. Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 50 N·m, then reconnect the high-pressure line and tighten it to 47 N·m; reconnect the electrical connector and spill connection.
  7. Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
  8. Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
Tips & Warnings:
  • Verify part number EJBR00801Z and the listed cross references against the vehicle’s EPC before fitting.
  • Torque the injector mounting/hold-down to 50 N·m.
  • Torque the high-pressure line to 47 N·m.
06

Frequently Asked Questions

QHow do I verify the old part and fitment?

Compare the old injector’s part number to EJBR00801Z and the listed cross references: EJBR01301Z, EJBR01601Z, 1141218, 2S7Q-9K546-AF, 1307096, 2S7Q-9K546-AH. Fitment is listed for Ford Mondeo III 2.0 TDCi (HJBC) 2001-2007 and Ford Transit IV 2.0 TDCi (F3FA) 2002-2006 in the Puma 2.0 TDCi, HJBC, HJBB engine family. Confirm the exact vehicle application against its EPC before ordering.

QWhat fault codes can point to this injector?

The listed diagnostic trouble codes for this common-rail diesel injector are P0300, P0087, P0201, P0204, and P0202. The system pressure is 1600 bar. No further symptom list is stated, so confirm further diagnosis against the vehicle’s EPC.

QIs coding or adaptation required after fitting this injector?

The supplied facts do not state coding or adaptation requirements for this common-rail diesel injector. Confirm the requirement against the vehicle’s EPC before fitting rather than guessing.

QCan I reuse the seals, and what torque should I use?

The supplied facts do not state whether the seals can be reused, so confirm seal requirements against the vehicle’s EPC. For this common-rail diesel injector, the mounting/hold-down torque is 50 N·m and the high-pressure line torque is 47 N·m.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

P0300High

Random or Multiple Cylinder Misfire Detected

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol