DELPHI EJBR02101Z
Common Rail Injector for Ford Mondeo (Mk3) 2.0 TDCi
2S7Q-9F593-BA, 2S7Q-9F593-BB, 1219725, 137669328239294L094PBD1600 bar peak rail pressureProduct Overview
The Delphi EJBR02101Z is an authentic common rail diesel injector calibrated for Ford Mondeo (Mk3) and 2.0 TDCi engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and L094PBD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 3 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Ford Mondeo (Mk3) | 2.0 TDCi (FMBA/N7BA 130PS) | 2001-2004 |
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR02101Z |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | 🔗 Shared Nozzle (2 assemblies):EJBR01101Z |
| Hold Down Torque | 55 N·m |
| High-Pressure Line Torque | 25 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 3 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 55 N·m, then reconnect the high-pressure line and tighten it to 25 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Confirm part number EJBR02101Z and the listed cross references against the old injector before fitting.
- Tighten the mounting/hold-down to 55 N·m and the high-pressure line to 25 N·m.
- Check the vehicle's EPC for coding/adaptation and seal-reuse requirements before installation.
Frequently Asked Questions
Will this common-rail diesel injector fit my Ford Mondeo Mk3 2.0 TDCi?
It is listed for the Ford Mondeo (Mk3) 2.0 TDCi (FMBA/N7BA 130PS) (2001-2004). The engine family references are 2.0 TDCi, Puma, FMBA, and N7BA. Confirm fitment against the vehicle's EPC using part number EJBR02101Z before ordering.
How can I verify the old injector and cross references before ordering?
Check for part number EJBR02101Z and cross references EJBR01401Z, 2S7Q-9F593-BA, 2S7Q-9F593-BB, 1219725, and 1376693. Compare these against the old injector markings and the vehicle's EPC; if anything does not match, confirm before ordering.
What are the system pressure and torque figures for this injector?
The listed system pressure for this common-rail diesel injector is 1600 bar. The mounting/hold-down torque is 55 N·m. The high-pressure line torque is 25 N·m.
Does this injector need coding or adaptation, and which fault codes are listed?
Coding/adaptation requirements are not stated in the verified facts; confirm them against the vehicle's EPC or diagnostic procedure. The listed diagnostic trouble codes are P0300, P0301, P0087, P0201, and P0204. Do not guess coding or adaptation steps for this injector.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.