Delphi EJBR02401Z
common rail injector
33800-27800, 33801-2780028239294L136PRD1400 bar peak rail pressureProduct Overview
The Delphi EJBR02401Z is an authentic common rail diesel injector calibrated for Hyundai Matrix (FC) and D3EA engine applications. Operating at an engineered rail pressure of 1400 bar, this solenoid assembly features the precision 28239294 control valve and L136PRD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 3 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR02401Z |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 32 N·m |
| High-Pressure Line Torque | 30 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 3 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 32 N·m, then reconnect the high-pressure line and tighten it to 30 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Confirm EJBR02401Z, EJBR01901Z, 33800-27800, and 33801-27800 against the vehicle's EPC before ordering.
- Tighten the mounting/hold-down fasteners to 32 N·m.
- Tighten the high-pressure line to 30 N·m.
Frequently Asked Questions
How do I confirm this injector fits my Hyundai and matches the old part?
EJBR02401Z is a common-rail diesel injector listed for Hyundai Matrix (FC) 1.5 CRDi (D3EA) 2001-2007 and Hyundai Getz (TB) 1.5 CRDi (D3EA) 2003-2005. Cross references are EJBR01901Z, 33800-27800, and 33801-27800. Confirm the number on the old injector and against the vehicle's EPC before ordering.
What fault codes or symptoms indicate a failed injector?
The listed diagnostic trouble codes are P0300, P0087, P0201, P0202, and P0203. Any other symptoms or testing steps are not stated in the verified facts and must be confirmed against the vehicle's EPC instead of guessing.
Does this injector need coding or adaptation after installation?
Coding/adaptation requirements for EJBR02401Z are not stated in the verified facts. Confirm coding/adaptation against the vehicle's EPC instead of guessing.
Can I reuse the seals, and what torque values should I use?
Reuse of seals is not stated in the verified facts and must be confirmed against the vehicle's EPC instead of guessing. Mounting/hold-down torque is 32 N·m, and high-pressure line torque is 30 N·m. System pressure is 1400 bar.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.