DELPHI EJBR02201Z
Common Rail Injector for Ford Focus (Mk1) 1.8 TDCi
1S4Q-9F593-AF, 1S4Q-9F593-AG, 1376691, 1141218, 4M5Q-9F593-FA28239294L087PBD1400 bar peak rail pressureProduct Overview
The Delphi EJBR02201Z is an authentic common rail diesel injector calibrated for Ford Focus (Mk1) and 1.8 TDCi engine applications. Operating at an engineered rail pressure of 1400 bar, this solenoid assembly features the precision 28239294 control valve and L087PBD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 3 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR02201Z |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | 🔗 Shared Nozzle (2 assemblies):EJBR01401Z |
| Hold Down Torque | 47 N·m |
| High-Pressure Line Torque | 25 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 3 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 47 N·m, then reconnect the high-pressure line and tighten it to 25 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Confirm EJBR02201Z fitment against the vehicle's EPC before installation.
- Verify that system pressure is 1400 bar for this common-rail diesel injector application.
- Tighten the mounting/hold-down fasteners to 47 N·m and the high-pressure line to 25 N·m.
Frequently Asked Questions
Does part EJBR02201Z fit my Ford 1.8 TDCi?
EJBR02201Z is listed for Ford Focus Mk1 1.8 TDCi (F9DA/F9DB) 2001-2004, Ford Transit Connect 1.8 TDCi (BHPA/HCPA) 2002-2006, and Ford Tourneo Connect 1.8 TDCi (HCPA) 2002-2006. The listed engine family references are 1.8 TDCi, Lynx, F9DA, F9DB, and FFDA. Confirm the vehicle application against the vehicle's EPC before ordering or fitting.
Which symptoms or diagnostic trouble codes should I check for a failed unit?
The listing gives diagnostic trouble codes P0300, P0087, P0201, P0204, and P0202 for this common-rail diesel injector. It does not state a symptom list or expected service life, so confirm those details against the vehicle's EPC.
Does this injector need coding or adaptation after fitting?
The verified facts do not state coding or adaptation requirements for EJBR02201Z. Confirm coding and adaptation requirements against the vehicle's EPC before fitting this common-rail diesel injector.
How can I verify the old injector and cross references?
Check the old unit for part number EJBR02201Z and compare it with cross references EJBR01302Z, EJBR01601Z, 1S4Q-9F593-AF, 1S4Q-9F593-AG, 1376691, and 1141218. If the marking or application is unclear, confirm against the vehicle's EPC rather than guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.