Delphi EJBR02601Z
common rail injector
A6650170121, 665017012128239294L137PRD1600 bar peak rail pressureProduct Overview
The Delphi EJBR02601Z is an authentic common rail diesel injector calibrated for SsangYong Rexton (Y200) and D27DT engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and L137PRD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 3 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR02601Z |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 42 N·m |
| High-Pressure Line Torque | 40 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 3 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 42 N·m, then reconnect the high-pressure line and tighten it to 40 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Confirm the exact vehicle application and part number against the EPC before ordering.
- Tighten the mounting/hold-down to 42 N·m and the high-pressure line to 40 N·m.
- Scan for DTCs P0300, P0087, P0201, P0204, and P0202 before replacing the injector.
Frequently Asked Questions
Is EJBR02601Z the correct common-rail diesel injector for my SsangYong?
EJBR02601Z is listed for SsangYong Rexton (Y200) 2.7 XDi (D27DT) 2004-2006 and Rodius I 2.7 XDi (D27DT) 2005-2012. Cross references are EJBR04501D, A6650170121, and 6650170121. Confirm the exact vehicle application and part number against the vehicle's EPC before ordering.
What diagnostic trouble codes or symptoms point to this injector?
The verified diagnostic trouble codes for this listing are P0300, P0087, P0201, P0204, and P0202. Specific symptoms are not stated in the verified facts, so scan the vehicle and confirm the fault before replacing the injector.
Does this common-rail diesel injector need coding or adaptation after installation?
Coding or adaptation requirements are not stated in the verified facts. This must be confirmed against the vehicle's EPC instead of guessing before installation.
What are the mounting and high-pressure line torques for this injector?
Mounting/hold-down torque is 42 N·m, and high-pressure line torque is 40 N·m. This injector is rated for a 1600 bar common-rail diesel system, so confirm the correct vehicle procedure before work.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.