Catalog / DELPHI / EJBR02501Z
DELPHI

Delphi EJBR02501Z

View Specs
SolenoidDelphi Common Rail SystemEuro 4

common rail injector

Reference data for DELPHI EJBR02501Z common rail injector · OEM 1307096, 4S7Q-9K546-BD, C2S30044 · Application Puma 2.0 TDCi, FMBA, N7BA
OE REFERENCE1307096, 4S7Q-9K546-BD, C2S30044
CONTROL VALVE28239294
NOZZLEL138PRD
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

WORKSHOP NOTICEECU Calibration / IMA Coding Required

This injector requires 6-8 digit calibration code programming (IMA / QR code) into the vehicle ECU (using Bosch KTS, Lexia/Diagbox or equivalent diagnostic equipment) following replacement to balance cylinder fuel delivery and prevent DTC P0300 misfire codes.

The Delphi EJBR02501Z is an authentic common rail diesel injector calibrated for Ford Mondeo III and Puma 2.0 TDCi engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and L138PRD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 4 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.

Before You Order

Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

OEM Ref
OE Nozzle
03

Vehicle & Engine Fitment

VehicleEngineYears
Ford Mondeo III2.0 TDCi (FMBA)2003-2007
Jaguar X-Type (X400)2.0 D (FMBA)2003-2009
04

Technical Specifications

SpecificationValue
SKUEJBR02501Z
BrandDELPHI
Fuel SystemCommon Rail (Delphi DFI)
Operating PressureCore Spec
Control ValveCore Spec
🔗 Shared Valve (40 assemblies):EJBR02301ZEJBR02401ZEJBR02601ZEJBR02701Z
Nozzle CodeCore Spec
Hold Down Torque50 N·m
High-Pressure Line Torque47 N·m
Coding RequiredYes
Emission StandardEuro 4
05

Installation Tips

  1. Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
  2. Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
  3. Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
  4. Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
  5. Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
  6. Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 50 N·m, then reconnect the high-pressure line and tighten it to 47 N·m; reconnect the electrical connector and spill connection.
  7. Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
  8. Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
Tips & Warnings:
  • Confirm the vehicle application against the EPC using EJBR02501Z, the listed cross references, and the VIN before fitting.
  • Tighten the mounting/hold-down to 50 N·m and the high-pressure line to 47 N·m.
  • Check diagnostic trouble codes P0300, P0087, P0201, P0204, and P0202 during diagnosis and confirm the fault path before replacing the injector.
06

Frequently Asked Questions

QWhat vehicles is this common-rail diesel injector listed for?

This common-rail diesel injector, part number EJBR02501Z, is listed for Ford Mondeo III 2.0 TDCi (FMBA) 2003-2007 and Jaguar X-Type (X400) 2.0 D (FMBA) 2003-2009. It is associated with the Puma 2.0 TDCi, FMBA and N7BA engine family. Always confirm the exact application against the vehicle's EPC using the VIN.

QWhat symptoms or fault codes indicate this injector may be faulty?

The listing provides diagnostic trouble codes P0300, P0087, P0201, P0204 and P0202, but it does not list specific symptoms for this injector. Use manufacturer diagnostics to confirm whether those codes relate to this unit before replacement. Do not guess at fault definitions beyond the listed codes.

QDoes this injector require coding or adaptation after installation?

The listing does not state whether coding or adaptation is required for EJBR02501Z. Confirm coding/adaptation requirements against the vehicle's EPC and manufacturer diagnostic information before installation. Do not assume a procedure that is not stated for this part.

QHow can I verify the old injector before ordering a replacement?

Compare the old unit's markings with part number EJBR02501Z and the listed cross references EJBR04601D, 1307096, 4S7Q-9K546-BD and C2S30044. If the markings do not match or are unclear, confirm fitment against the vehicle's EPC using the VIN rather than guessing.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0201High

Injector Circuit Malfunction - Cylinder 1

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

P0204High

Cylinder 4 Injector Circuit Malfunction / Open Circuit

P0300High

Random or Multiple Cylinder Misfire Detected

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

Workshop Diagnostic Protocol

Common Rail Injector Back-Leak Testing Guide

Common rail injector backleak test protocol. Graduated cylinder setup, warm idle & cranking limits in mL/min, control valve wear & P0087 diagnosis.

Read Technical Protocol
ECU Calibration Protocol

Bosch IMA Injector Coding & Location Guide

Bosch common rail injector IMA coding guide. Locate laser-etched 6-9 digit codes on body, ECU OBD2 adaptation steps & test bench calibration facts.

Read Technical Protocol
COMMON RAIL DIESEL WORKSHOP SOP

Stuck Injector Removal & Carbon Cleaning SOP | FuelPartsDB

Comprehensive workshop SOP for stuck diesel injector removal, pneumatic vibro-puller extraction, carbon solvent softening, and seat reaming without damage.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol