DELPHI EJBR02801D
Common Rail Injector for Kia Carnival (II) / Sedona J3
33800-4X500, 33801-4X500, 33800-4X80028239294L121PBD1600 bar peak rail pressureProduct Overview
The Delphi EJBR02801D is an authentic common rail diesel injector calibrated for Kia Carnival (II) / Sedona and J3 engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and L121PBD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 3 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR02801D |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 34 N·m |
| High-Pressure Line Torque | 28 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 3 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 34 N·m, then reconnect the high-pressure line and tighten it to 28 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Verify the old injector against EJBR02801D and the cross references EJBR00801Z, 33800-4X500, 33801-4X500, and 33800-4X800.
- Apply 34 N·m mounting/hold-down torque and 28 N·m high-pressure line torque.
- Scan for P0300, P0087, P0201, P0204, and P0202 before and after fitting this common-rail diesel injector.
Frequently Asked Questions
Will this injector fit my Kia Carnival II / Sedona 2.9 CRDi or Hyundai Terracan 2.9 CRDi?
It is listed for the Kia Carnival (II) / Sedona 2.9 CRDi (J3) from 2001-2006 and the Hyundai Terracan 2.9 CRDi (J3 16V) from 2001-2006. The listed engine families are J3, 2.9 CRDi, and J3 TCI. Confirm fitment against the vehicle's EPC before ordering.
How can I verify the old injector part number?
Compare the old injector with part number EJBR02801D and the cross references EJBR00801Z, 33800-4X500, 33801-4X500, and 33800-4X800. If the markings are unclear, confirm the old part against the vehicle's EPC instead of guessing.
Which DTCs are listed for this injector, and is coding or adaptation required?
The verified diagnostic trouble codes are P0300, P0087, P0201, P0204, and P0202. Coding or adaptation requirements are not stated in the verified facts and must be confirmed against the vehicle's EPC.
What are the mounting/hold-down and high-pressure line torque values?
The verified mounting/hold-down torque is 34 N·m, and the high-pressure line torque is 28 N·m. These are the only torque figures stated in the verified facts.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.