Delphi EJBR02901D
common rail injector
33800-4X800, 33801-4X80028239294L169PRD1600 bar peak rail pressureProduct Overview
The Delphi EJBR02901D is an authentic common rail diesel injector calibrated for Kia Carnival II (VQ) and J3 CRDi engine applications. Operating at an engineered rail pressure of 1600 bar, this solenoid assembly features the precision 28239294 control valve and L169PRD nozzle. Mandatory ECU calibration requires programming the cylinder-specific C2i 16-digit hexadecimal code into the engine control unit to establish smooth delivery balance and Euro 4 emissions compliance. Typical failure symptoms include control valve erosion causing excessive back-leakage, rail pressure deficit (DTC P0087), and erratic cold-start idling. Overhauling necessitates clean room assembly and genuine replacement seals.
Verify Delphi C2i/C3i calibration code and OEM cross reference before installation.
Technical Specifications
| Specification | Value |
|---|---|
| SKU | EJBR02901D |
| Brand | DELPHI |
| Fuel System | Common Rail (Delphi DFI) |
| Operating PressureCore Spec | |
| Control ValveCore Spec | |
| Nozzle CodeCore Spec | |
| Hold Down Torque | 38 N·m |
| High-Pressure Line Torque | 35 N·m |
| Coding Required | Yes |
| Emission Standard | Euro 4 |
Installation Tips
- Depressurize And Clean: Depressurize the fuel system and isolate it according to the workshop procedure, then clean the surrounding area of the injector bore and the cylinder head before opening any connection.
- Disconnect Connections: Disconnect the electrical connector and the spill/return connection from the injector, then plug or cover all exposed ports and fittings to prevent dirt ingress.
- Remove High-Pressure Line: Remove the high-pressure line from the injector inlet, cap or plug the line and the injector port immediately, and keep the line ends clean.
- Extract Old Unit: Release and remove the hold-down device, extract the old injector from the bore, and remove any old seals without damaging the cylinder head or injector bore.
- Clean Bore And Seat: Clean the injector bore and seat in the cylinder head, remove carbon and debris, inspect the sealing surfaces, and keep the area covered until the new injector is ready.
- Fit Seals And Seat Unit: Fit new seals to the injector, seat the unit in the injector bore, tighten the hold-down to 38 N·m, then reconnect the high-pressure line and tighten it to 35 N·m; reconnect the electrical connector and spill connection.
- Calibration Coding: Record the 20-digit Delphi C2i/C3i calibration code and program it with a suitable diagnostic tool.
- Leak-Check And Start-Up: Leak-check the high-pressure line and injector connections, start the engine, and inspect for fuel leaks and abnormal running; stop the engine if any leak is found.
- Verify EJBR02901D and the listed cross references against the old injector before installation.
- Torque the injector mounting/hold-down to 38 N·m.
- Torque the high-pressure line to 35 N·m.
Frequently Asked Questions
Will this EJBR02901D injector fit my Kia or Hyundai?
It is listed for Kia Carnival II (VQ) 2.9 CRDi (J3) 2006-2014, Kia Sedona II 2.9 CRDi (J3) 2006-2014, and Hyundai Terracan (HP) 2.9 CRDi 4WD (J3) 2003-2006. For any other vehicle or variant, confirm fitment against the vehicle's EPC.
What fault codes are listed for this common-rail diesel injector?
The listed diagnostic trouble codes are P0300, P0087, P0201, P0204, and P0202. Confirm code interpretation for the specific vehicle against its EPC.
What torque values should I use for installing this injector?
The mounting/hold-down torque is 38 N·m. The high-pressure line torque is 35 N·m.
How do I verify the old injector part number and cross references?
The part number is EJBR02901D, and the listed cross references are EJBR03701D, 33800-4X800, and 33801-4X800. Compare the old injector markings with these references, and confirm any uncertain match against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.