Catalog / DENSO / PE01-13-350
DENSO

DENSO PE01-13-350

View Specs
SolenoidGDI High-Pressure Fuel Pump (HPFP)Euro 6

High Pressure Fuel Pump Mazda Skyactiv G 2.0L 2.5L

Reference data for DENSO PE01-13-350 high-pressure fuel pump · OEM PE01-13-350A, PE01-13-350B, PE01-13-350C, PY01-13-350 · Application Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo (PE-VPS / PY-VPS / PY-VPTS)
OE REFERENCEPE01-13-350A, PE01-13-350B, PE01-13-350C, PY01-13-350
CONTROL VALVEINTEGRATED SOLENOID SUCTION CONTROL SPILL VALVE (SCV)
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Denso PE01-13-350 (Mazda OE PE01-13-350A / PE01-13-350B / PY01-13-350) is the genuine original equipment high-pressure fuel pump for Mazda Skyactiv-G 2.0L and 2.5L naturally aspirated and turbocharged engines. Driven by the exhaust camshaft via an anti-friction bucket lifter, this Denso single-piston pump delivers up to 200 bar (20 MPa) injection pressure. Standard fitment on Mazda 3, Mazda 6, CX-5, and CX-30 models, it features an integrated electronic suction control valve. Typical failure symptoms include long start cranking times, surging idle, and diagnostic code P0087.

Before You Order

HIGH-COMPRESSION GDI MISFIRE & SUCTION VALVE STICKING: Mazda Skyactiv-G engines utilize an ultra-high 13:1 to 14:1 compression ratio, requiring precise 200 bar fuel delivery. When the Denso PE01-13-350 suction control valve sticks from fuel varnish or the internal discharge check valve leaks, low rail pressure causes severe cold-engine hesitation, misfire codes P0300/P0301, and DTC P0087 under highway load.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Mazda 3PE-VPS / PY-VPS / PY-VPTS2014-2023
Mazda CX-5PE-VPS / PY-VPS / PY-VPTS2013-2023
Mazda Mazda 6 2.5PE-VPS / PY-VPS / PY-VPTS2014-2021
04

Technical Specifications

SpecificationValue
Pump GenerationDenso Single-Plunger High-Pressure Mechanical Fuel Pump
Operating Rail PressureCore Spec
Cam Drive TypeExhaust Camshaft via Anti-Friction Bucket Lifter
Flow Regulation ControlIntegrated Solenoid Suction Control Spill Valve (SCV)
Pump Flange Mounting Torque10 N·m + 90° (Even cross-pattern)
High Pressure Pipe Flare Nut Torque28 N·m
Tightening Torque28 N·m
Primary OEM ReferencePE01-13-350, PE01-13-350A, PE01-13-350B, PY01-13-350
Engine Emission ComplianceEuro 6 / LEV III / Tier 3 Bin 30
Standard Industrial Warranty12 Months / Unlimited Mileage

Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)

Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.

DENSOExact Engine & Chassis Match
PE01-13-250
Gasoline Direct Injection (GDI) • 200 bar
🚙 Mazda 3 (PEVPS)
Technical Specifications & Pinout
DENSOExact Engine & Chassis Match
PY01-13-250
Gasoline Direct Injection (GDI) • 200 bar
🚙 Mazda 3 (PEVPS)
Technical Specifications & Pinout
DENSOExact Engine & Chassis Match
PY8W-13-250
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code PEVPS
Technical Specifications & Pinout
05

Installation Tips

Tools needed: 10mm socket and torque wrench calibrated for 10-30 N·m, 17mm line flare wrench for fuel line pipe nut, Clean engine oil for pump O-ring seal lubrication, Clean lint-free shop cloths and eye protection

  1. Disconnect negative battery terminal; depressurize fuel system before loosening fittings.
  2. Loosen high-pressure fuel line union nut slowly to vent residual fuel pressure safely.
  3. Disconnect electrical wiring connector from SCV spill valve solenoid.
  4. Disconnect low-pressure fuel supply hose.
  5. Loosen the two pump flange bolts evenly in half-turn increments to release spring tension.
  6. Remove pump body; inspect bucket lifter for surface wear or galling.
  7. Clean cylinder head mating surface and coat new O-ring seal with clean motor oil.
  8. Rotate engine until driving camshaft lobe is on base circle (lowest lift point).
  9. Seat pump square into bore; thread mounting bolts finger-tight.
  10. Torque mounting bolts alternately to 10 N·m plus an additional 90-degree angle turn.
  11. Hand-thread high-pressure pipe flare nut; torque to 28 N·m.
  12. Reconnect fuel lines and electrical harness; prime system and check for leaks.
Tips & Warnings:
  • Angle Torque Specification: Always follow the 10 N·m + 90° specification; undertorquing allows vibration loosening while overtorquing strips aluminum threads.
  • Inspect Lifter Surface: Check the bucket lifter contacting the camshaft for scratches; replace lifter if discolored or worn.
  • Lubricate O-Ring: Never install the pump dry; lubricate the Viton O-ring with clean engine oil to prevent tearing during installation.
06

Frequently Asked Questions

QWhat are the common symptoms of a bad HPFP on a Mazda CX-5 or Mazda 3?

Common symptoms include extended cranking before the engine starts, jerky acceleration at highway speeds, a flashing or steady Check Engine Light with code P0087 (Fuel Rail Pressure Too Low), and rough idle hunting.

QWhat is the installation torque for the Mazda Skyactiv HPFP bolts?

Tighten the two flange bolts evenly to 10 N·m (89 lb-in) plus a 90-degree angle turn. Torque the high-pressure steel line pipe nut to 28 N·m (20.7 lb-ft). Always lubricate the O-ring seal with clean engine oil.

QAre Skyactiv-G 2.0L and 2.5L high-pressure fuel pumps interchangeable?

Yes, PE01-13-350 and its superseded part numbers (PE01-13-350A, PE01-13-350B) share identical physical mounting and electrical connectors across both 2.0L and 2.5L naturally aspirated Skyactiv-G engines.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol