DENSO PE01-13-250
Direct Fuel Injector Mazda 3 6 CX 5 CX 9 CX 30 2.0L 2.5L SkyActiv G 297500 1120
PE01-13-250A, PE01-13-250B, 297500-1120, FJ1202--200 bar peak rail pressureProduct Overview
The DENSO PE01-13-250 is a factory precision fuel injection component engineered specifically for the Mazda 2.0L PE-VPS & 2.5L PY-VPS SkyActiv-G DOHC 16V. Manufactured to strict original equipment tolerances, it delivers precise fuel atomization and operates up to its rated pressure of 200 bar (2900 psi). Common operational failure symptoms that point directly to this assembly include: Persistent Diagnostic Trouble Codes such as P0300, P0301, P0302, P0171 stored in the ECM. Hard cold starting, erratic idle oscillations, and severe acceleration stumbling. Unburnt fuel smell in the exhaust, black tailpipe soot, or fuel dilution in the engine crankcase. Loss of high-RPM power and engine protection limp-mode activation under highway load.
Always verify the OE reference PE0113250A, PE0113250B, 2975001120, FJ1202 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. PE01-13-250 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| sku | PE01-13-250 |
| brand | DENSO |
| manufacturer_code | 297500-1120 |
| pressure_rating | 200 bar (2900 psi) |
| torque_flange | 10 N-m (89 lb-in) |
| torque_line | 22 N-m (16 lb-ft) |
| engine_family | Mazda 2.0L PE-VPS & 2.5L PY-VPS SkyActiv-G DOHC 16V |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Always replace single-use high-pressure fuel lines and Teflon/copper sealing washers before installation.
- Lubricate the pump roller tappet or injector O-rings with clean engine oil before guiding into place.
- Tighten mounting flange fasteners in an even criss-cross pattern to 10 N-m (89 lb-in).
- Hand-thread fuel rail fittings first, then torque high-pressure flare nuts to 22 N-m (16 lb-ft) using a calibrated crowfoot wrench.
- Cycle the low-pressure fuel pump multiple times and perform a physical leak inspection before engine ignition.
- Torque the injector hold-down to 10 N·m.
- Torque the high-pressure line to 22 N·m.
- Verify the system pressure is 200 bar.
Frequently Asked Questions
Which Mazda models and years does PE01-13-250 fit?
PE01-13-250 is listed for Mazda 3 (2014-2023), Mazda CX-5 (2013-2023), and Mazda 6 2.5 (2014-2021) with PE-VPS, PY-VPS, or PY-VPTS. It is for the Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo engine family. Confirm final fitment against the vehicle's EPC.
Which diagnostic trouble codes are listed for this gasoline direct-injection injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302, and P0304. The verified facts do not provide further symptom descriptions for PE01-13-250.
Does PE01-13-250 require coding or adaptation after installation?
The verified facts do not state any coding or adaptation requirement for PE01-13-250. Confirm coding/adaptation against the vehicle's EPC instead of guessing.
Can I reuse the seals when fitting this injector?
The verified facts do not state whether seals can be reused with PE01-13-250. Confirm seal reuse against the vehicle's EPC instead of guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.