Catalog / DENSO / PY8W-13-250
DENSO

DENSO PY8W-13-250

View Specs
SolenoidGasoline Direct Injection (GDI / HDEV)Euro 4

High Pressure Fuel Injector Mazda CX 9 CX 5 Mazda 6 2.5L SkyActiv G Turbo PY01 13 250A

Reference data for DENSO PY8W-13-250 common rail injector · OEM PY01-13-250A, 297500-1120 · Application Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo (PE-VPS / PY-VPS / PY-VPTS)
OE REFERENCEPY01-13-250A, 297500-1120
CONTROL VALVEHIGH-SPEED SOLENOID ACTUATED MULTI-HOLE NOZZLE
NOZZLE-
EMISSIONEuro 4
WARRANTY12 Months
01

Product Overview

The Denso PY8W-13-250 (PY01-13-250A) is a multi-hole direct gasoline injector for Mazda 2.0L and 2.5L SkyActiv-G engines, including the 2.5T turbo variants (PE-VPS / PY-VPS / PY-VPTS). The fitment list covers the Mazda CX-9 (2016-2023), CX-5 (2019-2023) and Mazda 6 (2018-2022) 2.5L Turbo. It runs at rail pressures up to 200 bar (20 MPa / 2900 psi) and uses a multi-hole asymmetrical fan pattern matched to the high compression ratio. Rail holding bracket fasteners take 10 N·m and the high-pressure pipe flare nut 25 N·m; coil resistance is 1.8-2.2 Ω at 20°C. Common diagnostic codes are P0300, P0301-P0304 and P0171. A new Teflon combustion chamber seal ring and sizing collar are required before cylinder head installation.

Before You Order

Always verify the OE reference PY0113250A, 2975001120 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. PY8W-13-250 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Mazda CX-9 (TC)2.5L SkyActiv-G Turbo 186kW2016-2023
Mazda CX-5 (KF)2.5L SkyActiv-G Turbo 170kW2019-2023
Mazda 6 (GL)2.5L SkyActiv-G Turbo 170kW2018-2022
04

Technical Specifications

SpecificationValue
System TypeDenso Multi-Hole Direct Gasoline Fuel Injector
Operating PressureCore Spec
Spray PatternMulti-hole asymmetrical fan pattern optimized for high compression ratio
Fuel Rail Bolt Torque10 N·m (holding bracket flanged fasteners)
High Pressure Pipe Torque25 N·m Flare Nut Connection
Coil Resistance1.8 - 2.2 Ω at 20°C (High performance peak-and-hold drive)
Common Fault CodesP0300 (Random Misfire), P0301-P0304 (Cylinder Misfire), P0171 (System Too Lean Bank 1)
Workshop PrecautionReplace Teflon combustion chamber seal ring and sizing collar prior to cylinder head installation

Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)

Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.

DENSOExact Engine & Chassis Match
PY01-13-35Z
Gasoline Direct Injection (GDI) • 200 bar
🚙 Mazda 6 (Gl) (PEVPS)
Technical Specifications & Pinout
DENSOExact Engine & Chassis Match
PE01-13-350
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code PEVPS
Technical Specifications & Pinout
DENSOExact Engine & Chassis Match
PE01-13-350B
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code PEVPS
Technical Specifications & Pinout
HITACHIExact Engine & Chassis Match
PE19-13-350B
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code PEVPS
Technical Specifications & Pinout
DENSOExact Engine & Chassis Match
PE19-20-3F0
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code PEVPS
Technical Specifications & Pinout
DENSOExact Engine & Chassis Match
PY8W-13-350
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code PEVPS
Technical Specifications & Pinout
05

Installation Tips

  1. Depressurize Fuel Rail & Remove Intercooler Charge Piping: Depressurize fuel injection system via fuel pump fuse pull. Remove top-mount intercooler and intake charge tubes to access the center fuel rail.
  2. Disconnect Direct Injector Harness & Fuel Rail Lines: Unplug injector electrical connectors. Disconnect high pressure steel fuel rail line (25 N·m) and unbolt fuel rail mounting bolts (10 N·m).
  3. Extract Injectors & Fit New Teflon Chamber Seals: Carefully remove injectors with puller tool. Fit new Teflon chamber seals using the installation mandrel and compression die.
  4. Torque Rail Fasteners & Verify Pressure Integrity: Press injectors into cylinder head. Tighten rail bolts to 10 N·m. Torque steel high pressure line to 25 N·m. Start engine and verify zero fuel leakage.
Tips & Warnings:
  • Before fitting, confirm injector coding and adaptation requirements in the vehicle's workshop manual.
  • Inspect the mating area and confirm the correct part number PY8W-13-250 before installation.
  • If diagnosis is unclear, check the vehicle's EPC and workshop data rather than guessing from symptoms.
06

Frequently Asked Questions

QWhich applications is this injector listed for?

It is listed for the Mazda SkyActiv-G Turbo applications shown above, including the listed CX SUV and sedan fitments; confirm your VIN and EPC before ordering.

QWhat symptoms suggest a failed injector?

Look for misfire, rough idle, hesitation, poor power, fuel smell, or mixture-related faults; confirm diagnosis before replacing, as other faults can mimic an injector.

QWhat should I check before ordering?

Confirm the part number PY8W-13-250 against the vehicle's EPC and verify the engine family and exact application; do not rely on appearance alone.

QMust the old unit be matched or adapted?

Matching or adaptation requirements are not stated here; confirm coding and adaptation needs against the vehicle's EPC or workshop manual before fitting.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0200Critical

Fuel Injector Circuit Malfunction (General / Common Driver Stage)

P0201Critical

Injector Circuit Malfunction - Cylinder 1

P0300Critical

Random or Multiple Cylinder Misfire Detected

P0202High

Cylinder 2 Injector Circuit Malfunction / Open Circuit

P0203High

Cylinder 3 Injector Circuit Malfunction / Open Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
DIESEL WORKSHOP DIAGNOSTIC SOP

Cylinder Balance & Injector Deviation Guide

Common rail diesel cylinder balance & smooth running diagnostic guide. Balance rates, mg/stroke deviation, P0263 misfire, compression vs injector test.

Read Technical Protocol
ASSEMBLY & INSTALLATION PROTOCOL

Diesel Injector Torque Specs & TTY Angles Guide

Common rail diesel injector hold-down bolt torque specs, TTY angles & pipe unions. Covers Bosch, Detroit DD13, Cummins & VAG 2.0 TDI workshop data in Nm.

Read Technical Protocol