KEIHIN 16790-5LA-A01
High Pressure Fuel Pump Honda CR V Civic Accord 1.5T Earth Dreams L15B7
HM10035, GDP301--200 bar peak rail pressureProduct Overview
The 16790-5LA-A01 is an original equipment (KEIHIN) precision component engineered specifically for the Honda 1.5L Earth Dreams Turbo DOHC 16V (L15B7 / L15BA / L15BD). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0172, P0088, P219D.
Always verify the OE reference HM10035, GDP301 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 16790-5LA-A01 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16790-5LA-A01 |
| Manufacturer Brand | KEIHIN |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Honda 1.5L Earth Dreams Turbo DOHC 16V (L15B7 / L15BA / L15BD) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 12 N-m (106 lb-in) |
| Fuel Line / Rail Torque | 27 N-m (20 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0172, P0088, P219D |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 12 N-m (106 lb-in), and torque fuel line fittings to 27 N-m (20 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Torque the mounting/hold-down fasteners to 12 N·m.
- Torque the high-pressure line to 27 N·m.
- Confirm part number 16790-5LA-A01 and listed fitment against the vehicle’s EPC before ordering.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Honda 1.5L Turbo?
This part number is 16790-5LA-A01 and is listed for the Honda 1.5L Earth Dreams VTEC Turbo & i-VTEC engine family L15B7/L15BA/L15BE/L15B2. Listed fitment is Civic X 1.5 Turbo (2016-2021), CR-V V 1.5 Turbo (2017-2022), and Accord X 1.5 Turbo (2018-2022). Confirm the exact engine code and vehicle EPC before ordering.
What diagnostic trouble codes are listed for this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. Use the vehicle’s service diagnosis procedure; if a symptom or test specification is not stated here, confirm it against the vehicle’s EPC/service information rather than guessing.
Does this pump require coding or adaptation after installation?
The provided facts do not state any coding or adaptation requirement for this high-pressure fuel pump. Confirm coding/adaptation for the exact vehicle against the vehicle’s EPC or service information before installation.
Can I reuse the seals or high-pressure line?
The provided facts do not state seal or high-pressure line reuse guidance. Confirm that guidance against the vehicle’s EPC/service information; if installing the high-pressure line, the listed high-pressure line torque is 27 N·m.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.