KEIHIN 16010-5R1-315
Direct Fuel Injector Honda Fit GK5 Vezel HR V City 1.5L Earth Dreams L15B2
16010-5R1-305, 06160-5R1-305, FJ1236, 16010-5R1-316--200 bar peak rail pressureProduct Overview
The 16010-5R1-315 is an original equipment (KEIHIN) precision component engineered specifically for the Honda 1.5L i-VTEC Earth Dreams DOHC 16V (L15B2 / L15B3). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0302, P0171.
Always verify the OE reference 160105R1305, 061605R1305, FJ1236, 160105R1316 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 16010-5R1-315 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 16010-5R1-315 |
| Manufacturer Brand | KEIHIN |
| Component Type | Direct Fuel Injector |
| Engine Application | Honda 1.5L i-VTEC Earth Dreams DOHC 16V (L15B2 / L15B3) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 12 N-m (106 lb-in) |
| Fuel Line / Rail Torque | 12 N-m (106 lb-in) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0302, P0171 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 12 N-m (106 lb-in), and torque fuel line fittings to 12 N-m (106 lb-in).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the engine code and vehicle application against the EPC before ordering.
- Tighten the mounting/hold-down and high-pressure line to 12 N·m as specified.
- Check the listed DTCs P0300, P0301, P0087, P0302, and P0304 when diagnosing this injector.
Frequently Asked Questions
Will this injector fit my Honda Civic X 1.5 Turbo?
This injector is listed for Honda Civic X 1.5 Turbo with L15B7/L15BA/L15BE/L15B2 (2016-2021), Honda CR-V V 1.5 Turbo (2017-2022), and Honda Accord X 1.5 Turbo (2018-2022). Confirm fitment against the vehicle's EPC before ordering. The part number is 16010-5R1-315.
What symptoms or DTCs point to a failed injector?
The verified facts do not list symptoms; the diagnostic trouble codes listed are P0300, P0301, P0087, P0302, and P0304. Confirm the diagnosis against the vehicle's EPC before replacing the injector.
Does this injector require coding/adaptation, and can the seals be reused?
The verified facts do not state whether coding/adaptation is required or whether the seals can be reused. Confirm both points against the vehicle's EPC before installation.
How can I verify the old part and what is the expected service life?
Verify the old part by matching 16010-5R1-315 or the listed cross references: 160105R1315, 160105R1305, 061605R1305, FJ1236, 160105R1316, and 1601059B315. Expected service life is not stated, so confirm it against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.