CONTINENTAL 35310-2B020
Direct Fuel Injector Hyundai Elantra Veloster Kia Forte Soul 1.6L GDI G4FD
FJ1146, 842-12385--150 bar peak rail pressureProduct Overview
The 35310-2B020 is an original equipment (CONTINENTAL) precision component engineered specifically for the Hyundai Kia 1.6L Gamma GDI / T-GDI DOHC 16V (G4FD / G4FJ). Operating at peak injection pressures up to 150 bar (2175 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0300, P0301, P0302, P0172.
Always verify the OE reference FJ1146, 84212385 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 35310-2B020 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 35310-2B020 |
| Manufacturer Brand | CONTINENTAL |
| Component Type | Direct Fuel Injector |
| Engine Application | Hyundai Kia 1.6L Gamma GDI / T-GDI DOHC 16V (G4FD / G4FJ) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 10 N-m (89 lb-in) |
| Fuel Line / Rail Torque | 22 N-m (16 lb-ft) |
| Primary Diagnostic Fault Codes | P0300, P0301, P0302, P0172 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 10 N-m (89 lb-in), and torque fuel line fittings to 22 N-m (16 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Verify the old injector part number against 35310-2B020 and the listed cross references before replacement.
- Tighten the mounting / hold-down to 10 N·m and the high-pressure line to 22 N·m.
- Confirm the G4FD or G4FJ engine code and listed vehicle application in the EPC before ordering.
Frequently Asked Questions
Will this gasoline direct-injection injector fit my Hyundai or Kia 1.6L Gamma GDI / 1.6T T-GDI vehicle?
It is listed for the Hyundai/Kia 1.6L Gamma GDI & 1.6T T-GDI engine family (G4FD / G4FJ) and for Hyundai Sonata (2015-2019), Tucson (2015-2021), Veloster (2013-2020), and Kia Optima / K5 (2016-2020). The part number is 35310-2B020, with cross references 353102B020, FJ1146, 84212385, 353102B000, 353202B220 and 353202B140. Confirm your vehicle's engine code and application against the EPC before ordering.
What diagnostic trouble codes are listed for this injector?
The listed diagnostic trouble codes are P0300, P0301, P0087, P0302 and P0304. Use these as diagnostic clues and confirm the actual fault before replacing the injector.
Does this injector require coding or adaptation, and what service life should I expect?
Coding/adaptation requirements and expected service life are not stated in the supplied facts for part number 35310-2B020. Confirm them against the vehicle's EPC instead of guessing.
Can I reuse the seals, and what torque values and system pressure apply?
Seal reuse is not stated in the supplied facts; confirm it against the vehicle's EPC instead of guessing. The listed mounting / hold-down torque is 10 N·m, the high-pressure line torque is 22 N·m, and the system pressure is 150 bar.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.