Catalog / BOSCH / 35320-2B140
BOSCH

BOSCH 35320-2B140

View Specs
SolenoidGDI High-Pressure Fuel Pump (HPFP)Euro 6

High Pressure Fuel Pump Hyundai Elantra Tucson Kia Forte Sportage 1.6 GDI 0261520188

Reference data for BOSCH 35320-2B140 high-pressure fuel pump · OEM 35320-2B130, 0261520188, 0261520265 · Application Hyundai / Kia 1.6L Gamma GDI & 1.6T T-GDI (G4FD / G4FJ)
OE REFERENCE35320-2B130, 0261520188, 0261520265
CONTROL VALVEINTEGRATED ELECTRIC FLOW CONTROL VALVE (FCV)
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Bosch 35320-2B140 (Bosch 0261520188) is a Bosch HDP5 single-piston mechanical high-pressure fuel pump for Hyundai and Kia 1.6L Gamma GDI and 1.6T T-GDI engines (G4FD / G4FJ). It is listed for the Elantra 1.6 GDI (2016-2023), Tucson and Kia Sportage 1.6 T-GDI (2016-2022). A camshaft tri-lobe drives the internal piston against a rated rail pressure of 150 bar (15 MPa / 2175 psi), with delivery regulated by an ECU pulse-width-modulated flow control solenoid of 10.0-12.5 Ω at 20°C. Mounting flange bolts are tightened diagonally and progressively to 13 N·m, and the high-pressure pipe flare nut to 27 N·m. Common codes are P0087, P0088 and P1193. Before installation the internal roller tappet should be lubricated with fresh motor oil.

Before You Order

Always verify the OE reference 353202B130 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 35320-2B140 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Hyundai Elantra 1.6 GDI1.6L Gamma G4FD 97kW2016-2023
Hyundai Tucson1.6L Gamma G4FJ 130kW2016-2022
Kia Sportage1.6L Gamma G4FJ 130kW2016-2022
04

Technical Specifications

SpecificationValue
System TypeBosch HDP5 Single-Piston Mechanical High Pressure Fuel Pump
Operating PressureCore Spec
Actuation TypeCamshaft tri-lobe mechanical follower driving internal piston
Mounting Flange Bolt Torque13 N·m (diagonal progressive tightening in steps)
High Pressure Pipe Torque27 N·m Flare Nut Connection
Flow Control Solenoid Resistance10.0 - 12.5 Ω at 20°C (ECU PWM duty cycle regulated)
Common Fault CodesP0087 (Fuel Rail Pressure Too Low), P0088 (Pressure Too High), P1193 (Fuel Delivery Error)
Workshop PrecautionLubricate internal roller tappet with fresh motor oil prior to inserting into cylinder head housing

Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)

Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.

CONTINENTALExact Engine & Chassis Match
35310-2B020
Gasoline Direct Injection (GDI) • 150 bar
🚙 Hyundai Tucson (G4FD)
Technical Specifications & Pinout
KEIHINExact Engine & Chassis Match
35310-2B130
Gasoline Direct Injection (GDI) • 150 bar
🚙 Hyundai Tucson (G4FD)
Technical Specifications & Pinout
BOSCHExact Engine & Chassis Match
35310-2B000
Gasoline Direct Injection (GDI) • 150 bar
🚙 Engine Code G4FD
Technical Specifications & Pinout
05

Installation Tips

  1. Depressurize Fuel System & Position Camshaft: Depressurize fuel lines via fuel pump relay removal. Rotate crankshaft until camshaft pump lobe is at minimum base circle lift.
  2. Remove Steel High Pressure Pipe & Low Pressure Line: Disconnect low pressure quick-release rubber fuel hose. Disconnect steel high pressure flare nut (27 N·m) with backup counter-wrench.
  3. Unbolt HPFP Mounting Bolts & Inspect Roller Tappet: Unscrew two M6 mounting bolts alternately in half-turn increments to relieve spring preload. Inspect roller follower for surface wear.
  4. Fit New O-Ring, Torque Bolts Evenly & Test: Install new fluororubber O-ring lubricated with clean oil. Tighten mounting bolts alternately to 13 N·m. Torque steel line to 27 N·m. Start engine and check for leaks.
Tips & Warnings:
  • Tighten the pump mounting or hold-down fasteners to 13 N·m.
  • Tighten the high-pressure line to 27 N·m.
  • Verify part number 35320-2B140 and the listed cross references against the vehicle's EPC before installation.
06

Frequently Asked Questions

QWill this high-pressure fuel pump fit my Hyundai/Kia 1.6L GDI or T-GDI vehicle?

The verified fitment is Hyundai Elantra 1.6 GDI 1.6L Gamma G4FD 97kW (2016-2023), Hyundai Tucson 1.6L Gamma G4FJ 130kW (2016-2022), and Kia Sportage 1.6L Gamma G4FJ 130kW (2016-2022). It is the gasoline direct-injection high-pressure fuel pump with part number 35320-2B140. Confirm the vehicle's engine code and part number against the EPC before ordering.

QWhat diagnostic trouble codes are listed for this pump?

The verified diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. Specific failure symptoms are not stated in the verified facts, so diagnose from these codes and confirm the pump against the vehicle's EPC rather than guessing.

QDoes this high-pressure fuel pump need coding or adaptation after replacement?

Coding or adaptation requirements are not stated in the verified facts. This must be confirmed against the vehicle's EPC instead of guessing.

QHow can I verify the old high-pressure fuel pump before replacement?

Check the old pump for part number 35320-2B140 and compare it with the listed cross references: 353202B140, 353202B130, 0261520188, 0261520265, 353102B020, and 353102B130. Confirm the result against the vehicle's EPC before installation.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol