BOSCH 68305018AA
High Pressure Fuel Pump Jeep Wrangler JL Cherokee Alfa Romeo Giulia 2.0T Hurricane
68305018AB, 68252758AA, 0261520330, HPP0033, HM10031--200 bar peak rail pressureProduct Overview
The 68305018AA is an original equipment (BOSCH) precision component engineered specifically for the FCA GME T4 Hurricane 2.0L Turbo DOHC 16V (Jeep / Alfa Romeo). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P053F.
Always verify the OE reference 68305018AB, 68252758AA, HPP0033, HM10031 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 68305018AA needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Jeep Wrangler (JL) | EC1 | 2018-2024 |
| Jeep Grand Cherokee | EC1 | 2021-2024 |
| Alfa Romeo Giulia | EC1 | 2017-2024 |
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 68305018AA |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | FCA GME T4 Hurricane 2.0L Turbo DOHC 16V (Jeep / Alfa Romeo) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 13 N-m (115 lb-in) |
| Fuel Line / Rail Torque | 28 N-m (21 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P053F |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 13 N-m (115 lb-in), and torque fuel line fittings to 28 N-m (21 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the EC1 fitment against the vehicle's EPC before ordering or installing this pump.
- Torque the mounting/hold-down fasteners to 13 N·m and the high-pressure line to 28 N·m.
- Check the listed diagnostic trouble codes P0300, P0087, P0193, P0089, and P0191 during diagnosis.
Frequently Asked Questions
Will this high-pressure fuel pump fit my vehicle?
This part is listed for the Stellantis/FCA 2.0L GME T4 Hurricane Turbo (EC1 Jeep/Alfa Romeo). Listed fitment is Jeep Wrangler (JL) EC1 2018-2024, Jeep Grand Cherokee EC1 2021-2024, and Alfa Romeo Giulia EC1 2017-2024. Confirm the exact application against the vehicle's EPC before ordering.
What system pressure and torque specs apply to this pump?
The listed system pressure is 200 bar. The mounting/hold-down torque is 13 N·m, and the high-pressure line torque is 28 N·m. Use these listed values for the specified pump.
Does this pump require coding/adaptation, and can I reuse the seals?
Coding/adaptation requirements and seal reuse are not stated in the verified facts. Confirm both against the vehicle's EPC or service information before installation; do not guess.
How can I verify the old pump and what diagnostic trouble codes are listed?
Verify the old unit against the listed part number 68305018AA and cross references 68305018AA, 68305018AB, 68252758AA, 0261520330, HPP0033, and HM10031. The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. If identification is unclear, confirm against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.