BOSCH 50051491
High Pressure Fuel Pump Alfa Romeo Giulia Stelvio Jeep Wrangler 2.0T GME T4 0261520371
68348370AA, 68348370AB, 0261520371--200 bar peak rail pressureProduct Overview
The 50051491 is an original equipment (BOSCH) precision component engineered specifically for the Alfa Romeo-Stellantis 2.0L GME T4 Hurricane MultiAir Turbocharged DOHC 16V I4 (GME T4 / EC1). Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference 68348370AA, 68348370AB stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 50051491 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Jeep Wrangler (JL) | EC1 | 2018-2024 |
| Jeep Grand Cherokee | EC1 | 2021-2024 |
| Alfa Romeo Giulia | EC1 | 2017-2024 |
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | 50051491 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Alfa Romeo-Stellantis 2.0L GME T4 Hurricane MultiAir Turbocharged DOHC 16V I4 (GME T4 / EC1) |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 12 N-m (106 lb-in) |
| Fuel Line / Rail Torque | 28 N-m (21 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 12 N-m (106 lb-in), and torque fuel line fittings to 28 N-m (21 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the vehicle EPC fitment for part 50051491 before ordering.
- Tighten the pump mounting/hold-down fasteners to 12 N·m and the high-pressure line to 28 N·m.
- Check the old pump against the listed cross references, including 68348370AA, 68348370AB, 0261520371, 0261520448, and 68305018AA.
Frequently Asked Questions
Will part 50051491 fit my 2018-2024 Jeep Wrangler JL EC1?
Part 50051491 is listed for the Jeep Wrangler (JL) ["EC1"] (2018-2024) with the Stellantis/FCA 2.0L GME T4 Hurricane Turbo engine family. The listing also covers Jeep Grand Cherokee ["EC1"] (2021-2024) and Alfa Romeo Giulia ["EC1"] (2017-2024). Confirm fitment against the vehicle EPC before ordering.
What diagnostic trouble codes are listed for this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. No symptom descriptions or test procedures are provided in the verified facts, so confirm diagnosis and part replacement against the vehicle service information and EPC.
What are the mounting and high-pressure line torques for this pump?
The mounting/hold-down torque is 12 N·m, and the high-pressure line torque is 28 N·m. The listed system pressure is 200 bar. For any fastener or specification not listed here, confirm against the vehicle EPC or service information.
Does this high-pressure fuel pump require coding or adaptation after installation?
Coding or adaptation requirements are not stated in the verified facts for part 50051491. Confirm the required procedures against the vehicle EPC or service information rather than guessing.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.