DENSO PY01-13-35Z
High Pressure Fuel Pump Mazda CX 9 CX 5 Mazda 6 CX 50 2.5T Skyactiv G Turbo PY VPTS
PY01-13-35ZA, PY01-13-35ZBINTEGRATED FLOW REGULATING SOLENOID VALVE-200 bar peak rail pressureProduct Overview
The DENSO PY01-13-35Z is an OEM Tier-1 precision-engineered fuel system component built to strict factory tolerances. Engineered for modern high-performance gasoline engines, this component delivers precise fuel metering, maintains stable fuel rail pressure, and mitigates cold-start misfire, engine oil dilution, and acceleration hesitation under demanding driving conditions.
Always verify the OE reference PY011335ZA, PY011335ZB stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. PY01-13-35Z needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Mazda Skyactiv-G 200-bar Direct Injection High-Pressure System |
| Operating PressureCore Spec | |
| Pump Mechanism | Cylinder Head Mounted Camshaft-Driven Plunger Pump |
| Quantity Control ValveCore Spec | |
| Injector Hold-Down Bolt Torque | 14 N·m (124 in-lb) flange mounting bolts📐 Torque & Angle Wizard → |
| Fuel Line Nut Torque | 28 N·m (21 lb-ft) high-pressure pipe union nut |
| Flange Seal | Replaceable High-Temperature Viton O-Ring |
| Manufacturer | DENSO (OEM for Mazda Motor Corporation) |
| Mazda Part Number | PY01-13-35Z / PY01-13-35ZA / PY01-13-35ZB |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- High-Pressure Fuel Pressure Relief & Battery Safety: Disconnect negative battery terminal. Remove fuel pump fuse and crank engine for 5 seconds to depressurize the 200-bar fuel rail. Allow turbocharger assembly to cool completely.
- Engine Cosmetic Cover & Intake Ducting Disassembly: Remove Skyactiv-G engine cover and unbolt upper intercooler pipe and bracket assemblies to expose the high-pressure fuel pump mounted on the cylinder head cover.
- Electrical Connector & Fuel Line Detachment: Disconnect the fuel pressure control valve connector. Using a 17mm flare nut wrench, loosen high-pressure steel delivery pipe union nuts (counter-holding pump fitting). Release low-pressure supply line clamp.
- Camshaft Base Circle Alignment & Pump Removal: Turn crankshaft pulley clockwise until the high-pressure pump camshaft drive lobe is at base circle to minimize spring load. Alternately loosen mounting bolts 1/2 turn at a time and remove pump.
- Roller Tappet Inspection & New Pump Installation: Inspect roller tappet inside head bore for scoring or surface fatigue. Lubricate new pump O-ring with fresh synthetic oil. Place pump square on head and torque bolts alternately to 14 N·m.
- High-Pressure Tube Torquing & Diagnostic Fuel Pressure Test: Thread high-pressure tube nuts by hand, then torque flare nuts to 28 N·m. Reinstall intercooler ducting. Cycle ignition key ON-OFF 3 times, inspect for fuel leaks, and verify actual fuel rail pressure via OBD2.
- Tighten the mounting/hold-down fasteners to 14 N·m.
- Tighten the high-pressure line to 28 N·m.
- Verify the replacement part number against the vehicle EPC before installation.
Frequently Asked Questions
Will this PY01-13-35Z high-pressure fuel pump fit my Mazda?
This PY01-13-35Z gasoline direct-injection high-pressure fuel pump is listed for 200 bar system pressure and Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo (PE-VPS / PY-VPS / PY-VPTS) applications. Fitment includes Mazda CX-9 (TC) 2.5T Skyactiv-G Dynamic Pressure Turbo (2016-2023), CX-5 (KF) 2.5T (2019-2024), Mazda 6 (GL) 2.5T (2018-2021), and CX-50 (VA) 2.5T (2023-2024). Confirm the exact application against the vehicle EPC before ordering.
What symptoms or DTCs can point to a failed high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. The verified facts do not include a specific symptom list, so use these codes with normal vehicle diagnostics and confirm the failed pump diagnosis before replacement.
Does this pump require coding/adaptation, and can I reuse the seals?
The verified facts do not state coding/adaptation requirements or seal reuse guidance for this high-pressure fuel pump. Confirm both points against the vehicle’s EPC or service information instead of guessing.
How can I verify the old pump/part number before replacement?
Check the old unit for part number PY01-13-35Z and cross references PY011335Z, PY011335ZA, PY011335ZB, 0261520288, 12698944, and 16625AA040. Confirm the exact application against the vehicle EPC before fitting the replacement.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.