BOSCH A2640900200
High Pressure Fuel Pump Mercedes C260 C300 E300 GLC300 1.5T 2.0T M264 M254 0261520521
2640900200, A2640900100, 2640900100, HPP0038, HM10046, 0261520521--200 bar peak rail pressureProduct Overview
The A2640900200 is an original equipment (BOSCH) precision component engineered specifically for the Mercedes-Benz 1.5L & 2.0L Turbocharged DOHC 16V M264 / M254 EQ Boost. Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P053F, P0171.
Always verify the OE reference 2640900200, A2640900100, 2640900100, HPP0038 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. A2640900200 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
| Vehicle | Engine | Years |
|---|---|---|
| Mercedes-Benz C-Class (W205/W206) / E-Class (W213) | M264 / M254 | 2018-2024 |
| Mercedes-Benz GLC (X253/X254) / GLE (V167) / CLS | M264.920 / M254.920 | 2019-2024 |
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | A2640900200 |
| Manufacturer Brand | BOSCH |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Mercedes-Benz 1.5L & 2.0L Turbocharged DOHC 16V M264 / M254 EQ Boost |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 20 N-m (15 lb-ft) |
| Fuel Line / Rail Torque | 27 N-m (20 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P053F, P0171 |
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 20 N-m (15 lb-ft), and torque fuel line fittings to 27 N-m (20 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Tighten the pump mounting/hold-down fasteners to 20 N·m.
- Tighten the high-pressure line to 27 N·m.
- Confirm exact fitment and any coding/seal requirements against the vehicle's EPC before installation.
Frequently Asked Questions
Which Mercedes-Benz models and engines does part A2640900200 fit?
Part A2640900200 is a gasoline direct-injection high-pressure fuel pump for Mercedes-Benz 1.5L & 2.0L Turbocharged DOHC 16V M264 / M254 EQ Boost engines, with 200 bar system pressure. Fitment is listed for C-Class W205/W206 and E-Class W213 with M264/M254 (2018-2024), plus GLC X253/X254, GLE V167, and CLS with M264.920/M254.920 (2019-2024). Confirm exact fitment by VIN against the vehicle's EPC before ordering.
What diagnostic trouble codes are listed for this high-pressure fuel pump, and can they indicate a failed unit?
The listed diagnostic trouble codes for this pump are P0300, P0087, P0193, P0089, and P0191. Use these codes with the vehicle's diagnostic procedure; the verified facts do not include a symptom-by-symptom diagnosis or service-life interval. If the code or symptom is not covered, confirm against the vehicle's EPC/service information rather than guessing.
Does this high-pressure fuel pump require coding/adaptation, and can the mounting seals be reused?
Coding/adaptation requirements and seal reuse are not stated in the verified facts, so confirm them against the vehicle's EPC/service information. When installing the pump, the mounting/hold-down torque is 20 N·m and the high-pressure line torque is 27 N·m. Do not guess any additional torque or adaptation value.
How can I verify the old part and cross-reference numbers for A2640900200?
Check the old pump against the cross references A2640900200, 2640900200, A2640900100, 2640900100, HPP0038, and HM10046. The component is a gasoline direct-injection high-pressure fuel pump for the listed M264/M254 applications. If the markings do not match, confirm the replacement against the vehicle's EPC before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.