HITACHI PE19-13-350B
High Pressure Fuel Pump Mazda CX 5 CX 4 Axela Atenza 2.0L 2.5L SKYACTIV G HPP0022
PE19-13-350A, HPP0022--200 bar peak rail pressureProduct Overview
The PE19-13-350B is an original equipment (HITACHI) precision component engineered specifically for the Mazda 2.0L (PE-VPS) & 2.5L (PY-VPS) SKYACTIV-G DOHC 16V Direct Injection I4. Operating at peak injection pressures up to 200 bar (2900 psi), this unit delivers micro-metered fuel atomization required for high thermal efficiency, responsive low-end torque, and compliant tailpipe emissions. Common symptoms indicating component failure include rough idle shivering, extended cold-cranking intervals (5-10 seconds), unburned fuel odor in the engine oil, and active engine malfunction codes such as P0087, P0088, P0171, P2293.
Always verify the OE reference PE1913350A, HPP0022 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. PE19-13-350B needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| Part Number / SKU | PE19-13-350B |
| Manufacturer Brand | HITACHI |
| Component Type | Mechanical High Pressure Fuel Pump (HPFP) |
| Engine Application | Mazda 2.0L (PE-VPS) & 2.5L (PY-VPS) SKYACTIV-G DOHC 16V Direct Injection I4 |
| Operating PressureCore Spec | |
| Mounting Torque (Flange / Bracket) | 14 N-m (124 lb-in) |
| Fuel Line / Rail Torque | 28 N-m (21 lb-ft) |
| Primary Diagnostic Fault Codes | P0087, P0088, P0171, P2293 |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System: Pull fuel pump fuse or disconnect LPFP harness. Crank engine 5-8 seconds until it stalls to drop residual rail pressure below 5 bar.
- Clean Surrounding Cavity: Blow compressed air around cylinder head bore or pump flange cavity to prevent dirt ingress into the fuel rail.
- Lubricate & Fit Seals: Inspect Teflon combustion seals or O-rings. Coat lightly with clean motor oil (do not use grease) to avoid tearing during insertion.
- Torque to Factory Specification: Hand-thread bolts evenly. Tighten mounting fasteners to 14 N-m (124 lb-in), and torque fuel line fittings to 28 N-m (21 lb-ft).
- Prime & Leak Check: Cycle ignition to RUN position 3 times (5 seconds each) to build low-side pressure. Inspect fittings for leaks before starting engine.
- Confirm the engine code and VIN/EPC fitment before ordering the PE19-13-350B pump.
- Tighten the mounting hold-down to 14 N·m and the high-pressure line to 28 N·m.
- Check the listed DTCs—P0300, P0087, P0193, P0089, and P0191—against service information before replacing the pump.
Frequently Asked Questions
Will this gasoline direct-injection high-pressure fuel pump fit my Mazda 3, CX-5, or Mazda 6?
This gasoline direct-injection high-pressure fuel pump is listed for Mazda 3 (2014-2023), CX-5 (2013-2023), and Mazda 6 2.5 (2014-2021) with PE-VPS, PY-VPS, or PY-VPTS engine codes. The engine family is Mazda 2.0L & 2.5L SkyActiv-G / 2.5T Turbo. Confirm VIN/EPC fitment before ordering.
What are the mounting and high-pressure line torque specs?
The mounting / hold-down torque is 14 N·m. The high-pressure line torque is 28 N·m, and the listed system pressure is 200 bar.
Which diagnostic trouble codes are listed for this high-pressure fuel pump?
The listed DTCs are P0300, P0087, P0193, P0089, and P0191. Use them as diagnostic references and confirm the actual fault against the vehicle's service information.
How can I verify the old pump before ordering, and do I need coding or new seals?
Compare the old unit against PE19-13-350B and the cross references PE1913350B, PE1913350A, HPP0022, PE0113250, PE0113350, and PE0113350B. Coding/adaptation and seal-reuse requirements are not stated in the verified facts; confirm them against the vehicle's EPC/service information before installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.