Catalog / DENSO / 23100-25010
DENSO

DENSO 23100-25010

View Specs
SolenoidGDI High-Pressure Fuel Pump (HPFP)Euro 6

D 4S High Pressure Fuel Pump Toyota Camry RAV4 Avalon Lexus ES 250 2.5L Dynamic Force A25A FKS 2310025010

Reference data for DENSO 23100-25010 high-pressure fuel pump · OEM 23100-F0010, GDP512 · Application Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS)
OE REFERENCE23100-F0010, GDP512
CONTROL VALVEINTEGRATED HIGH-SPEED DIGITAL FLOW CONTROL SOLENOID
NOZZLE-
EMISSIONEuro 6
WARRANTY12 Months
01

Product Overview

The Denso 23100-25010 (Toyota reference 2310025010, alternate part number 23100-F0010) is the original equipment high-pressure mechanical fuel pump (HPFP) engineered for Toyota's revolutionary 2.5-liter Dynamic Force 4-cylinder engine (A25A-FKS). Operating within Toyota's D-4S dual-injection framework (combining direct and port fuel injection), this camshaft-actuated single-plunger pump provides fuel pressures up to 200 bar (2900 psi) for top-selling models including the Toyota Camry (XV70), RAV4 (XA50), Avalon, and Lexus ES 250. When high-mileage pumps deteriorate, drivability issues emerge during the transition between port and direct injection. Technicians frequently trace hesitation, cold start surging, and extended cranking to diagnostic trouble code P0087 (Fuel Rail/System Pressure Too Low). In advanced failure states, internal plunger shaft seal wear allows pressurized fuel to leak past the pump body into the cylinder head timing gallery, diluting engine oil and creating a pungent gasoline smell on the dipstick. Installation requires strict adherence to Toyota factory service specifications. Mounting bolts must be torqued evenly to 21 N·m (15 lb-ft), and the high-pressure fuel pipe union nut tightened to 30 N·m (22 lb-ft). Technicians must inspect the roller tappet and change engine oil and filter immediately if fuel dilution is confirmed.

Before You Order

Always verify the OE reference 23100F0010, GDP512 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 23100-25010 needs no ECU calibration coding; no code transfer is required after fitting.

Technical references: OEM service documentation, manufacturer catalogs, and field repair data.
02

Compatible Injectors

Primary
OEM Ref
03

Vehicle & Engine Fitment

VehicleEngineYears
Toyota Camry (XV70)Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS)2018-2024
Toyota RAV4 (XA50)Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS)2019-2024
Lexus ES 250Toyota / Lexus 2.0L & 2.5L Dynamic Force D-4S (A25A-FKS / A25A-FXS / M20A-FKS)2021-2024
04

Technical Specifications

SpecificationValue
System TypeToyota D-4S Dual Injection (Direct & Port) 200-bar System
Operating PressureCore Spec
Pump MechanismCamshaft Driven Single-Piston Plunger Mechanical Pump
Mounting Flange Bolt Torque21 N·m (15 lb-ft) flange bolts
Fuel Line Nut Torque30 N·m (22 lb-ft) high-pressure fuel pipe union nut
Drive InterfaceRoller Lifter Tappet with Hardened Contact Face
Flow Control SolenoidIntegrated High-Speed Pulse-Width Modulated Solenoid Actuator
ManufacturerDenso (Tier-1 OEM for Toyota Motor Corporation)
Denso Production Reference23100-25010 / GDP512

Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)

Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.

DENSOExact Engine & Chassis Match
23209-24010
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code A25AFKS
Technical Specifications & Pinout
DENSOExact Engine & Chassis Match
23209-25010
Gasoline Direct Injection (GDI) • 200 bar
🚙 Engine Code A25AFKS
Technical Specifications & Pinout
05

Installation Tips

  1. Fuel System Residual Pressure Relief: Depressurize fuel system by removing the fuel pump fuse from the engine bay junction box and cranking engine until it stalls. Disconnect negative battery cable.
  2. Engine Cover & Sound Insulator Removal: Remove plastic engine cover and acoustic foam damper surrounding the high-pressure fuel pump assembly on the cylinder head.
  3. High-Pressure Delivery Pipe Disconnection: Unscrew the high-pressure delivery pipe union nuts with a flare nut wrench while counter-holding pump fitting. Discard single-use flared pipe.
  4. Pump Removal & Roller Tappet Inspection: Evenly loosen the two mounting bolts in half-turn steps to relieve spring preload. Lift pump and inspect roller tappet bucket for scuffing or scoring.
  5. New Pump Installation & Final Torque Sequence: Lubricate new O-ring with fresh engine oil. Turn engine until camshaft drive lobe is at base circle. Torque mounting bolts to 21 N·m (15 lb-ft) and line union nut to 30 N·m (22 lb-ft).
Tips & Warnings:
  • Never reuse high-pressure fuel pipes: Toyota mandates replacement of steel fuel delivery pipes whenever loosened to prevent fuel spray hazards.
  • Inspect roller lifter bucket: A scored or worn roller tappet damages the camshaft drive lobe, necessitating expensive camshaft replacement.
  • Verify engine oil for fuel dilution: A failing internal pump seal weeps fuel into the timing cover, causing oil level rise and bearing wear.
  • Prime fuel circuit prior to cranking: Turn ignition ON for 5 seconds 3 times to prime low-pressure feed and purge air pockets.
06

Frequently Asked Questions

QWhich vehicles is 23100-25010 listed for?

It is listed for specific Toyota Camry and Lexus ES applications plus the other Toyota application shown in the fitment data, all in the listed Toyota/Lexus Dynamic Force petrol engine family. Confirm by VIN/EPC.

QWhat symptoms suggest this high-pressure fuel pump has failed?

The supplied data does not list failure symptoms. Diagnose the vehicle using the workshop manual and confirm the pump part number is 23100-25010 against the EPC before replacing.

QWhat should I check before ordering this pump?

Confirm the vehicle matches the listed Camry, Lexus ES, or other Toyota application for the Dynamic Force petrol family, and verify the required part number is 23100-25010 using VIN/EPC.

QDoes the replacement pump need coding or adaptation?

Coding or adaptation requirements are not stated in the supplied data. Check the vehicle's workshop manual or EPC for matching instructions before installation.

07

Diagnostic Trouble Codes & Fault Protocols

Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:

P0087Critical

Fuel Rail/System Pressure Too Low

P0088Critical

Fuel Rail/System Pressure Too High

P0089Critical

Fuel Pressure Regulator 1 Performance

P0191Critical

Fuel Rail Pressure Sensor 'A' Circuit Range/Performance

P0002High

Fuel Volume Regulator Control Circuit Range / Performance (VCV / IMV)

P0090High

Fuel Pressure Regulator 1 Control Circuit

08

Cross-Reference & Compatibility

Sister parts, same-platform variants, and known incompatibilities.

Technical Diagnostic & Service Protocols

Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.

COMMON RAIL WORKSHOP DIAGNOSTICS

Common Rail High-Pressure Pump Diagnostics Guide

Diagnose common rail high-pressure pump failure: suction vacuum, CP4 roller glitter, plunger wear, air ingress & P0087 hard start. Workshop bench testing.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Fuel Metering Valve (IMV/SCV) Diagnostics Guide

Diagnostic guide for common rail fuel metering valves (IMV/SCV/FCA/MPROP). Normally open vs closed, coil resistance, PWM duty cycle & P0088 / P0089 test.

Read Technical Protocol
OBD-II DIAGNOSTIC PROTOCOL

P0087 Low Rail Pressure Diagnosis Guide

Step-by-step workshop diagnostic protocol for OBD-II DTC P0087 (Fuel Rail Pressure Too Low). 5-stage troubleshooting tree: backleak testing, SCV valve, PRV valve, and high-pressure pump.

Read Technical Protocol
COMMON RAIL WORKSHOP DIAGNOSTICS

Rail Pressure Relief Valve Diagnostics Guide

Common rail pressure relief valve (PRV) testing guide. Diagnose hot start stalls, P0087 rail pressure loss, return line leakage & single vs 2-stage valves.

Read Technical Protocol