DENSO 23209-31100
D 4S High Pressure Direct Fuel Injector Toyota Tacoma Highlander Sienna Lexus RX 350 3.5L V6 2GR FKS 297500 0110
297500-0110, 23209-0P040, 23290-31100SLIT-NOZZLE ATOMIZING DIRECT INJECTION HIGH-PRESSURE SOLENOID-200 bar peak rail pressureProduct Overview
The Denso 23209-31100 (Denso engineering code 297500-0110, cross-referenced with Toyota OEM 23209-0P040 and 23290-31100) is the original equipment Tier-1 high-pressure direct fuel injector specifically developed for Toyota's advanced 3.5-liter V6 Dynamic Force / Atkinson-capable engine family (2GR-FKS). Operating at pressures up to 200 bar (2900 psi), these precision injectors work in synchrony with port fuel injectors in Toyota's D-4S dual-injection architecture across high-demand vehicles including the Toyota Tacoma, Highlander, Sienna, Camry V6, Avalon, and Lexus RX 350 and ES 350. In real-world workshop environments, aged direct injectors on 2GR-FKS engines can accumulate fuel varnish and micro-lacquer along the pintle valve tip. When switching from low-speed port injection to high-load direct injection, clogged or sluggish direct injectors fail to spray sufficient volume, triggering DTC P0171 (System Too Lean Bank 1), intermittent hesitation during sudden acceleration, and occasional P0300 random cylinder misfires. Installing genuine Denso 23209-31100 direct injectors restores seamless power delivery and high-RPM fuel delivery. During replacement, hold-down clamp bolts must be tightened to 10 N·m (89 in-lb), and the high-pressure fuel supply pipe union to 30 N·m (22 lb-ft). Technicians must take care to install new PTFE combustion seals and verify that high-pressure fuel rail hold pressure stabilizes at specification after ignition key-off.
Always verify the OE reference 2975000110, 232090P040, 2329031100 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 23209-31100 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Toyota D-4S Dual Fuel Injection (Direct & Port) 200-bar System |
| Operating PressureCore Spec | |
| Spray Type | Laser-Drilled Dual-Slit and Multi-Hole Symmetrical Fan Pattern |
| Injector Hold-Down Bolt Torque | 10 N·m (89 in-lb) injector clamp retaining bolts📐 Torque & Angle Wizard → |
| Fuel Line Nut Torque | 30 N·m (22 lb-ft) high-pressure fuel pipe union joint bolt |
| Combustion Seal | High-Density Virgin PTFE Teflon Ring |
| Vibration Damper | Fluorocarbon (FKM) Resilient Bushing and Rail Seal |
| Manufacturer | Denso (Tier-1 OEM for Toyota Motor Corporation) |
| Denso Production Number | 297500-0110 |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Depressurize Fuel System via Toyota Techstream or Fuel Relay: Depressurize high-pressure fuel rail using diagnostic scanner or by removing fuel pump relay. Disconnect negative battery ground cable.
- Intake Manifold & Surge Tank Removal: Remove upper aluminum intake surge tank plenum, vacuum lines, and throttle body wiring to access Bank 1 and Bank 2 high-pressure fuel rails.
- High-Pressure Delivery Pipe Removal: Unscrew high-pressure fuel feed pipe unions using backup wrenches on hex flats. Remove fuel rail bracket mounting bolts.
- Direct Injector Extraction & Cylinder Head Bore Prep: Remove injector hold-down clamps and pull direct injectors straight from head. Clean carbon deposits from injector well seats using brass tools.
- New Injector Installation & Torque Procedure: Install new Denso 23209-31100 injectors with new Teflon seals. Tighten hold-down clamp bolts evenly to 10 N·m (89 in-lb), and fuel pipe union bolts to 30 N·m (22 lb-ft).
- Before installing 23209-31100, confirm the injector position and connector type against the vehicle's EPC.
- Work with a cool engine and follow the workshop manual's approved removal and installation sequence.
- After fitting, check for fuel leaks and verify smooth running before returning the vehicle.
Frequently Asked Questions
Will this injector fit my Toyota Tacoma or other listed applications?
It is listed for Toyota Tacoma, Toyota Highlander, and Lexus RX applications using the specified engine family. Confirm your VIN, engine code, and injector position against the vehicle's EPC before ordering.
What symptoms should I look for before replacing the injector?
Symptoms are not stated here; have misfire, idle quality, hesitation, and fuel-trim checks confirmed against the vehicle's workshop manual before replacing the injector.
What should I check before ordering this part?
Verify the part number 23209-31100 against the vehicle's EPC, confirm the engine family and injector position, and inspect the connector and fuel system for damage. Do not rely on visual similarity alone.
Must the replacement injector be coded or adapted?
Coding, matching, and adaptation requirements are not stated here; confirm them against the vehicle's EPC or workshop manual. Also verify whether any relearn or leak-check procedure is required after installation.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.