DENSO 23100-0P040
High Pressure Fuel Pump Toyota Tacoma Highlander Lexus RX350 3.5L 2GR FKS 294000 2440
23100-31040, 23100-0P010, 294000-2440INTEGRATED ELECTRONIC SPILL CONTROL VALVE (SCV)-200 bar peak rail pressureProduct Overview
The Denso 23100-0P040 (294000-2440) is a camshaft-driven single-plunger high-pressure mechanical fuel pump for Toyota and Lexus 3.5L V6 2GR-FKS / 2GR-FXS D-4S engines. It is listed for the Toyota Tacoma N300 (2016-2023), Highlander XU50 (2017-2022) and Lexus RX350 AL20 (2016-2022). An exhaust camshaft dual-lobe actuates the pump through a roller lifter to 200 bar (20 MPa / 2900 psi); the high-speed PWM spill control valve measures 1.9-2.3 Ω at 20°C. Flanged mounting bolts are torqued alternately to 21 N·m and the rigid steel flare pipe fitting to 30 N·m. Common codes are P0087, P0088 and P1078. The internal plunger O-ring should be lubricated with engine oil, and the roller lifter checked for free rotation and flat spots.
Always verify the OE reference 2310031040, 231000P010, 2940002440 stamped on your existing pump body before ordering; confirm the pump part number and drive coupling match your engine before unsealing the packaging. 23100-0P040 needs no ECU calibration coding; no code transfer is required after fitting.
Vehicle & Engine Fitment
Technical Specifications
| Specification | Value |
|---|---|
| System Type | Camshaft-Driven Single Plunger High-Pressure Mechanical Fuel Pump |
| Operating PressureCore Spec | |
| Actuation Method | Exhaust camshaft dual-lobe actuation through roller lifter |
| Flange Mounting Bolt Torque | 21 N·m (flanged mounting bolts torqued alternately) |
| High Pressure Line Torque | 30 N·m (rigid steel flare pipe fitting) |
| Spill Control Valve ResistanceCore Spec | |
| Common Fault Codes | P0087 (Fuel Rail Pressure Too Low), P0088 (Rail Pressure Too High), P1078 (Direct Injection Fault) |
| Workshop Precaution | Lubricate internal plunger O-ring with engine oil; verify roller lifter spins freely without flat spots |
Matched High-Pressure Fuel Injectors (Fuel Circuit Assembly)
Directly supplied by this high-pressure pump. Verify injector backleak balance if rail pressure fails to build during engine cranking.
Installation Tips
- Depressurize Fuel System & Remove Air Intake Ducting: Depressurize fuel line via scan tool command or fuel pump circuit opening relay. Unbolt intake resonator tube and engine appearance shield.
- Disconnect Spill Valve Connector & High Pressure Pipe: Unclip wiring harness from electronic spill control valve. Use flare wrench to counter-hold and disconnect high pressure delivery tube (30 N·m).
- Unbolt Mounting Flange & Inspect Roller Lifter: Loosen two flange bolts half-turn at a time to ease internal spring load. Withdraw HPFP and remove roller lifter from camshaft housing to check for scoring.
- Install Pump with Fresh O-Ring & Final Torque Fasteners: Fit new lubricated O-ring onto pump housing. Hand-thread mounting bolts and torque evenly to 21 N·m. Tighten fuel pipe flare nut to 30 N·m. Verify zero leaks.
- Confirm part number 23100-0P040 and the exact vehicle application against the EPC before installation.
- Torque the mounting/hold-down fasteners to 21 N·m and the high-pressure line to 30 N·m.
- Check the listed DTCs P0300, P0087, P0193, P0089, and P0191 before condemning the high-pressure fuel pump.
Frequently Asked Questions
Will this high-pressure fuel pump fit my Toyota Tacoma, Highlander, or Lexus RX350?
Part number 23100-0P040 is a gasoline direct-injection high-pressure fuel pump for the Toyota/Lexus 3.5L V6 2GR-FKS / 2GR-FXS D-4S & 2GR-FE Dual VVT-i engine family. Listed fitment is Toyota Tacoma N300 2016-2023, Toyota Highlander XU50 2017-2022, and Lexus RX350 AL20 2016-2022. Confirm the exact vehicle application against the vehicle’s EPC before ordering.
What DTCs should I check before replacing this high-pressure fuel pump?
The listed diagnostic trouble codes are P0300, P0087, P0193, P0089, and P0191. The verified facts do not provide a symptom list or code-to-failure mapping, so confirm any missing diagnostic criteria against the vehicle’s EPC instead of guessing. This part is a gasoline direct-injection high-pressure fuel pump with a 200 bar system pressure.
Does this pump require coding or adaptation, and can I reuse the seals?
Coding/adaptation requirements and seal reuse are not stated in the verified facts; confirm both against the vehicle’s EPC instead of guessing. Use the listed mounting/hold-down torque of 21 N·m and high-pressure line torque of 30 N·m when the procedure calls for them. This pump is part number 23100-0P040 for the listed Toyota/Lexus 3.5L V6 applications.
How can I verify whether the old pump is the correct 23100-0P040 unit?
Check the old pump for part number 23100-0P040 and compare the listed cross references: 231000P040, 2310031040, 231000P010, 2940002440, 0261520288, and 16625AA040. Also confirm the engine family and the listed Tacoma N300, Highlander XU50, or Lexus RX350 AL20 fitment against the vehicle’s EPC. Do not guess if the numbers or application do not match.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.