DENSO 23209-31050
Multi Hole Fuel Injector Toyota Camry Highlander RAV4 Lexus RX350 ES350 3.5L 2GR FE 23250 31050
23250-31050, 23209-0P040, 23250-0P040, FJ760, 842-12322--4 bar peak rail pressureProduct Overview
The DENSO 23209-31050 is a factory precision fuel injection component engineered specifically for the Toyota / Lexus 3.5L Dual VVT-i 24-Valve DOHC V6 2GR-FE. Manufactured to strict original equipment tolerances, it delivers precise fuel atomization and operates up to its rated pressure of 3.5 bar (51 psi). Common operational failure symptoms that point directly to this assembly include: Persistent Diagnostic Trouble Codes such as P0300, P0301, P0171, P0174 stored in the ECM. Hard cold starting, erratic idle oscillations, and severe acceleration stumbling. Unburnt fuel smell in the exhaust, black tailpipe soot, or fuel dilution in the engine crankcase. Loss of high-RPM power and engine protection limp-mode activation under highway load.
Always verify the OE reference 2325031050, 232090P040, 232500P040, FJ760 stamped on your existing injector body before ordering; confirm the engine code and injector part number on the unit body both match your vehicle before unsealing the packaging. 23209-31050 needs no ECU calibration coding; no code transfer is required after fitting.
Technical Specifications
| Specification | Value |
|---|---|
| sku | 23209-31050 |
| brand | DENSO |
| manufacturer_code | 23250-31050 |
| pressure_rating | 3.5 bar (51 psi) |
| torque_flange | 10 N-m (89 lb-in) |
| torque_line | 21 N-m (15 lb-ft) |
| engine_family | Toyota / Lexus 3.5L Dual VVT-i 24-Valve DOHC V6 2GR-FE |
Matched High-Pressure Fuel Pump (Fuel Circuit Assembly)
Operates on the same high-pressure rail circuit. When troubleshooting low rail pressure (DTC P0087), verify pump volumetric delivery before replacing injectors.
Installation Tips
- Always replace single-use high-pressure fuel lines and Teflon/copper sealing washers before installation.
- Lubricate the pump roller tappet or injector O-rings with clean engine oil before guiding into place.
- Tighten mounting flange fasteners in an even criss-cross pattern to 10 N-m (89 lb-in).
- Hand-thread fuel rail fittings first, then torque high-pressure flare nuts to 21 N-m (15 lb-ft) using a calibrated crowfoot wrench.
- Cycle the low-pressure fuel pump multiple times and perform a physical leak inspection before engine ignition.
- Confirm the vehicle's model, year, and engine code against the EPC before fitting part number 23209-31050.
- Tighten the mounting/hold-down fasteners to 10 N·m and the high-pressure line to 21 N·m.
- Use the listed DTCs P0300, P0301, P0087, P0302, and P0304 when checking for injector-related faults.
Frequently Asked Questions
Which vehicles and engines does part number 23209-31050 fit?
This multi-point (port) fuel injector is listed for Toyota Tacoma N300 with 2GR-FKS, 2GR-FXS, or 2GR-FE (2016-2023), Toyota Highlander XU50 with the same engine codes (2017-2022), and Lexus RX350 AL20 with the same engine codes (2016-2022). Confirm the exact vehicle fitment against the vehicle's EPC before ordering.
Which diagnostic trouble codes are listed for this fuel injector?
The listed DTCs are P0300, P0301, P0087, P0302, and P0304. Other symptom descriptions or diagnostic criteria are not stated in the supplied facts and must be confirmed against the vehicle's EPC or service information.
Can the seals be reused, and does this injector require coding or adaptation after installation?
Seal reuse and coding/adaptation requirements are not stated in the supplied facts. Confirm these points against the vehicle's EPC or service information instead of guessing.
How can I verify the old injector and what torque values apply?
Cross references for this part include 2320931050, 2325031050, 232090P040, 232500P040, FJ760, and 84212322; compare these with the old unit's part number or markings before replacement. Mounting/hold-down torque is 10 N·m, high-pressure line torque is 21 N·m, and system pressure is 4 bar. Confirm any value not listed here against the vehicle's EPC.
Diagnostic Trouble Codes & Fault Protocols
Common diagnostic trouble codes (DTCs) triggered when this common rail injector experiences wear, circuit faults, or calibration drift:
Random or Multiple Cylinder Misfire Detected
Cross-Reference & Compatibility
Sister parts, same-platform variants, and known incompatibilities.
Technical Diagnostic & Service Protocols
Authoritative field procedures, diagnostic testing thresholds, and service SOPs for this assembly.